What is the resulting flow rate in the system if three pumps are used in parallel? (a) 0.483 m^3/s (b) 0.364 m^3/s (c) 0.333 m^3/s (d) 0.563 m^3/s 1. The Head -flowrate curve for a centrifugal pump is given by: HP = 28 -30Q2 Where, HP is in meter and Q is in m3/s . This pump is used to pump water for a system with the following (H-Q) curve: HS = 8 + 150Q2 Where, HS is in meter and Q is in m3/s . IT SAYS : if theee pumps are used in parallel PAY ATTENTION Multiple choice choose correct answe

Q: 15. A pump operating at 660 hp delivers water, from a large pressurized supply tank to a large…

A: Given: The pump power, P = 660 hp The water flow rate, Q = 150 ft^3/s The total length, H = 1000 ft…

Q: (a) flow rate, in gpm; and (b) horsepower. Assume near-radial entry flow.

A:

Q: Propose a centrifugal pump (brand and model) to transport 10 L/s of a fluid with a density of 1500…

A: The discharge of the pump given at starting is- The head given is .The density of the fluid is .

Q: Ah against capacity Q pump and system curves for both pumps running on the basis of the O1. Two…

A:

Q: You want to pump water at a rate of 2 m^3/s from the lower to the upper reservoir. What type of pump…

A: Given   Flow rate, Q = 2 m3/s       Speed, N = 600 rpm      Friction, f = 0.01      Length, L = 20 m…

Q: Lecture Example 2 : An 18-in-diameter centrifugal pump, running at 880 rev/min and 156 brake…

A: Given :diameter of pump D = 18 inspeed of the pump initially, N1 = 880 rev/minBrake horsepower,  P =…

Q: In a test of the centrifugal pump shown in Fig. below, the following data are taken: py =100 mmHg…

A: The velocity of the fluid at inlet by using the continuity equation The velocity of the fluid at…

Q: Ex.2: In a test of the centrifugal pump shown in Fig. below, the following data are taken: pi 100…

A:

Q: A centrifugal pump has the following characteristics: V (m³/h) H (m) n (%) 23 46 69 92 115 16 13.5 2…

A: Given:Pipe length, L=800 mDiameter of pipe, d=15 cm or 0.15 mstatic head, hs=8 mTemperature of…

Q: A pump, geometrically similar to the 12.95-in model inFig. , has a diameter of 24 in and is to…

A: For water, ρ1 = 1.94 slug.ft3For gasoline, from Table A.3, ρ2 = 680 kg/m3 = 1.32 slug.ft3 From…

Q: In a test of the centrifugal pump shown in Fig. , thefollowing data are taken: p1= 100 mmHg (vacuum)…

A: Convert 100 mmHg = 13332 Pa, 500 mmHg = 66661 Pa, 180 gal/min =0.01136 m3/s.  Calculate the inlet…

Q: Two identical centrifugal pumps connected in series are used to pump water between two storage tanks…

A: Inner diameter of pipe, d=0.1 mTotal Equivalent length on the suction side, Ls=20 mTotal Equivalent…

Applied Fluid Mechanics

A fluid is a substance that is continuously deformed by the application of shear stress. The rate of deformation of a fluid depends on its viscosity. The fluid tries to flow when it interacts with some other system.