Example -5.2-It is required to pump cooling water from storage pond to a condenser in aprocess plant situated 10 m above the level of the pond. 200 m of 74.2 mm i.d.pipe is available and the pump has the characteristics given below. The headloss in the condenser is equivalent to 16 velocity heads based on the flow inthe 74.2 mm pipe. If the friction factor = 0.003, estimate the rate of flow andthe power to be supplied to the pump assuming n = 0.5Q (m³/s) 0.0028 0.0039 0.0050.0056 0.0059Ah (m)23.221.318.915.211.0

Please Rate if this solution helps youThank You

Answered: Example -5.2- It is required to pump…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

In a direct boosted cold water system to tanks the pressure of the water main is 350 kPa vertical height from main two tanks is 65 m and the required residual head at tanks is 3m. Calculate the required head of the boosting equipment in meters of water.
#3 fluid machineries. will upvote anyone who will answer, please make complete solution and corrects units. Thanks
A Forced - Draft (FDF) with open suction has rated capacity of 4,000 CFM at 1,800 rpm. The pressure developed at the discharged duct is 10 mm H2O. The discharge duct is circular with inside diameter of 600 mm. Calculate the following:a) what is the velocity of air at the discharge in mm H2O?b) what is the theoretical fan power required in kW?Consider standard density of water and air are 1000 kg/m3 and 1.20 kg/m
Water at 22oC is pumped from the bottom of a large storage tank where the pressure is 290 kPa gage to a nozzle which is 14.17 m above the tank bottom and discharges to the atmosphere with a velocity in the nozzle of 20.1 m/s. The water flow rate is 50 kg/s. The efficiency of the pump is 77% and 9 kW are furnished to the pump shaft.a. Draw the diagram b. The friction loss in the pump. c. The friction loss in the rest of the process.(include principles used)
F Q3: Water (p=990 kg/m³ & μ= 0.0013 Pa.s) is pumping from an atmospheric water tank to water injection well with carbon steel pipe has same level, where the discharge pipe diameter is 12 inch, pipe length is 4700 m, pipe roughness is 0.045 mm, and water flow rate is 0.065 m³/sec. 1- Calculate discharge head, if the pressure at water injection well is 190 bar. 2- Calculate pump liquid power, if pump section head value is 3.8 m.
PROBLEM 5 An axial flow pump is required to deliver 1m3/s at 7m head while running at 960 rpm. Its outer diameter is 50 and hub diameter is 25 cm. Find the following: (1) flow velocity, which is assumed to be constant from hub to tip, and A. 4.59 m/s B. 6.791 m/s C. 60.7 m/s D. 39.3 m/s (2) power required to drive the pump if overall efficiency is 84%. A. 81.75 kW B. 12.03 kW C. 40.7 kW D. 60.9 kW
A pitot-static tube is used to measure the velocity of water in a pipe. The stagnation pressure head is 6 m and static pressure head is 5 m. Calculate the velocity of flow assuming the co- efficient of tube equal to 0.98.
A. A water jet of diameter 180 mm impinges on the buckets of a Pelton turbine having overall efficiency of 85% while operating under a net head of 500 m and at speed of 420 rpm. Find the specific speed of the turbine. Take coefficient of velocity of the jet as 0.98 and speed ratio as 0.46. B. The pitch circle diameter of a Pelton wheel is 0.9 m. A jet of water of diameter 80 mm gets deflected by an angle of 170° when it impinges on the buckets. The bucket friction coefficient and coefficient of velocity of jet can be taken as 0.93 and 0.97 respectively. If the net head available on the wheel is 500 m and speed ratio is 0.45, calculate (a) the power transferred to to the wheel by the jet, (b) hydraulic efficiency, and (c) specific speed of the turbine. Take mechanical efficiency of wheel as 0.9.
A pitot static tube fitted in a pipe of 0.25 m diameter records the difference in stagnation and static pressure as 0.085 m of water. Assume the velocity coefficient as unity, calculate the water velocity in the pipe line.
Problem -1 A tank is initially empty. A liquid with p = 62.4 Ibm/ft is poured into the tank at a constant mass flow rate of mi = 7 lbm/s. The tank has cross-sectional area A = 0.2 fe, and the fluid in the tank has a %3D variable height H(t). There is a hole at the bottom of the tank. The fluid flows out of the tank at a rate proportional to the fluid height: rme = kH, where k= 1.4 lbm/ft/s. Find H(t). A sketch is given in Fig. P.1. Figure.P.1: Sketch of tank filling problem
It is required to pump cooling water from storage pond to a condenser in a process plant situated 10 m above the level of the pond. 200 m of 74.2 mm i.d.pipe is available and the pump has the characteristics given below. The head loss in the condenser is equivalent to 16 velocity heads based on the flow in the 74.2 mm pipe. If the friction factor -0.003, estimate the rate of flow and the power to be supplied to the pump assuming -0.5. Q(m/s) 0,0028 0.0039 0.005 0.0056 0.0059 23.2 21.3 18.9 15.2 11.0 ΔΗ (13)
For the single pump-pipe system below, what will be the changes for the operating point if we increase the pipe size but decrease the shaft speed of the pump? EB H₂ O The operating point will remain the same. O The operating point will occur either at a higher discharge or at a lower discharge, depending on the specific influence of each change. O The operating point will occur at a higher discharge. O The operating point will occur at a lower discharge.

SEE MORE QUESTIONS

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS