Compute using 4 decimal places and use scientific notation when necessaryBox all final answers.FIND:1. Under Unbalanced Condition Without Faults:b. Load Line Voltages (Vab, Vbc, Vca); GIVEN:Three-phase System Data:30 SourceZLine30 LoadEanZan = Zbn = Zen = 0.1 + j1.5 nSource:12020° v; Epn = 1202 – 120° v; Een = 1204120° v (grounded neutral)Line Impedance:Zline a = Zline bZline c = 1+ j2 N;CLoad Impedance:Zab40 + j30 N; Zbc = 40 – j30 N; Zca = 50 + j0 N%3D%3D

Under unbalanced condition without fault We have to find b) load line voltages

Answered: Under Unbalanced Condition Without…

Engineering

Electrical Engineering

Under Unbalanced Condition Without Faults: b. Load Line Voltages (Vab, Vbc, Vca);

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Consider the three-phase four-wire 416-V secondary system with balanced per-phase loads at A, B, and…

A: Given three phase four wire system

Q: fault location

A: Types of open circuit fault- 1) Symmetrical fault- Three phase line to ground fault Three phase…

Q: Q2. Explain the symmetrical fault analysis using ZbuS.

A: Note: As per the guidelines will be solving only 1st question. Repost for others Symmetrical fault…

Q: determine the per-unit impedances and the per-unit source voltage. Then cal- culate the load current…

A: Electricity moves through a single conductor in a single-phase connection. The three independent…

Q: 3.On a double line-to-ground faultImmersive reader A) The short-circuit currents in the faulted…

A: In this question , we will write about double line to ground fault....

Q: Problem 5 Consider the system shown in the single-line diagram of Figure (3). All reactances are…

A: Single Line Diagram: A single-line diagram, often known as an SLD, is an electrical diagram or…

Q: Q3/A/ Fill in the blanks: 1. The most common type of 3-phase unsymmetrical fault is 2. In a balanced…

A: The solution is given below

Q: A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout the…

A: x=1y=7Note: reactance of element right to bus 4 is not given. Hence we will not consider that in…

Q: ure shows a sample power system network and Zpus Matrix elements. For a solid three phase fault take…

Q: Figure shows a sample power system network and Zpus Matrix elements. For a solid three phase fault…

Q: In the figure below, all impedances are in per unit on a common MVA base. The generators are…

Q: Write in detail about cable fault location using Varley loop test.With appropiate diagram.

A: Write in detail about cable fault location using Varly loop test. With appropriate diagram.…

Q: pecified in per unit. For generators, assume Z* =Z` =j0.2, Z° = j0.05 For transformers, assume Z' =…

Q: the fault current for a

A: Types of open circuit fault- 1) Symmetrical fault- Three phase line to ground fault Three phase…

Q: The fault current level of a circuit breaker used in a transmission line with phase voltage 4.6 kV…

A: Fault current level? of the breaking capacity 70MVA Voltages = 4.6kV

Q: Q.3 When a line-to-ground fault occurs, the current in faulted phase 'a' is 100A. The zero-sequence…

A: Given- Line to ground fault- Current in the faulted phase=100 A, To Find- The zero-sequence current.

Q: Problem 7. Three-phase Balanced Fault Analysis. For the two-generator system below, a three-phase…

Q: For the network shown in the figure below, all reactances are in p.u. to a base of 100MVA and 13.8…

A: The power system is a network consist of power generation, transmission, and distribution. Power…

Q: Figure shows a sample power system network and Zpus Matrix elements. For a solid three phase fault…

A: Note: Here line impedance as well as Z bus matrix impedance are given We are going to solve the…

Q: 6. Two balanced delta connected loads are connected in parallel across a 230V, three phase, 3wire…

A: Given: Line Voltage, VL=230V Impedance per phase are 20cos30° and 40cos-45°

Q: b) A fault occurs at bus 2 of the network shown in Figure Q3. Pre-fault nodal voltages throughout…

Q: I. Draw the reactance diagram for the following power system in per unit using base power = 50 MVA…

Q: The LLLG fault occurs at bus-6 with pre-fault voltage as 1.05 p.u. If the positive sequence…

A: Given, The pre-fault voltage at bus-6 is V6 = 1.05 pu Positive sequence impedance at bus-7 is Z7 =…

Q: 7.In a line-to-ground fault we can expect that A) There are no currents to ground. B) The…

A: Single line to ground fault is asymetrical fault that makes the system unbalance. Sequence networks…

Q: b) A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout…

A: POWER SYSTEM: A power system is a network of electrical components that provide, transmit, and…

Q: The sample power system subjected to three phase fault at bus 4. The system values are given below

Q: Problem 1(B)- If the fault in Problem 1(A) was a Line-Line fault between phases B and C through a…

Q: Q1. Given Z, = 0.3L60º, Z¡ = 0.17L80° and, Z2 = 0.45L120°. Compute the fault current and voltages…

Q: Q.3 When a line-to-ground fault occurs, the current in faulted phase 'a' is 100A. The zero-sequence…

Q: 2_ What case/cases in which the measured phase current include the three symmetrical components (…

Q: Q2/The positive-sequence reactances for the power system shown in Figure are in per unit on a common…

A: Current: It is the time rate of the change of the charges. It is also known as the flow of the…

Q: The single line diagram of a power system is shown in Figure Q2.1 including generator and…

A: Given length of line =50 km MVA base = 100 MVA For line , base voltage =11 kV

Q: The system values are given below. The bus 1 voltage after fault =6.18 p.u. The bus 2 voltage after…

A: Following Data is given in the question V1 = 6.18 p.u. V2 = 2.54 p.u. Y12 =3.25 p.u. Fault Current…

Q: The sample large power system network data's are given below, The total number of buses is 5…

Q: Consider the single-line diagram of a power system shown below. The transient reactance of cach part…

A: The above question is based on symmetrical fault analysis. All reactances are already given in pu…

Q: d) Discuss the procedure for computation of fault current in power system when a double line to…

Q: Describe the concept of fault current analysis in power systems and its role in protecting…

A: Fault current analysis is a critical aspect of power system engineering that involves the…

Q: Q2/The positive-sequence reactances for the power system shown in Figure are in per unit on a common…

A: Given: The positive-sequence reactances for the power system shown in the figure are in per unit on…

Q: A 3-phase generator (30 MVA, 13.8 KV, 0.15) supplies two motors (rated at 20 MVA, 12.8 KV, 20%, and…

A: The one line diagram is shown below voltage in transmission line circuit=13.8×11513.2=120.23 kV…

Q: Consider the following statements about a 4 variable K-map: (a) cells in the top row are adjacent to…

A: Let us consider a digital circuit having a logical expression involving four variables.

Q: Describe the process of fault current analysis in power systems and its significance in protecting…

A: Fault current analysis in power systems is a critical process that involves calculating and…

Q: The sample large power system network data's are given below, The total number of buses is 5…

A: In this question we have to find fault current...From z bus matrix..

Q: Design a power system network consists of the following: į, 2 generators ii. 2 transformers iii. 2…

A: Power system network : An electric energy system is described as a community of electrical…

Concept explainers

Single Phase AC Circuit

Alternating Current (AC) is a type of electric power in which the electric current changes, both in magnitude and direction, at regular intervals. This AC Circuits can deliver power in either a Single Phase system or a Three Phase system.

Question

Compute using 4 decimal places and use scientific notation when necessary
Box all final answers.
FIND:
1. Under Unbalanced Condition Without Faults:
b. Load Line Voltages (Vab, Vbc, Vca);

GIVEN:
Three-phase System Data:
30 Source
ZLine
30 Load
Ean
Zan = Zbn = Zen = 0.1 + j1.5 n
Source:
12020° v; Epn = 1202 – 120° v; Een = 1204120° v (grounded neutral)
Line Impedance:
Zline a = Zline b
Zline c = 1+ j2 N;
C
Load Impedance:
Zab
40 + j30 N; Zbc = 40 – j30 N; Zca = 50 + j0 N
%3D
%3D

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

b) load line voltages

VIEW

Step by step

Solved in 4 steps with 7 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Analysis of Single Phase and Three Phase System

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

4.In a double line-to-ground fault we can expect thatImmersive reader A) There are currents in the ground connections. B) The current values in the ground connections are zero. C) Short-circuit currents exist in all three phases. D) The currents in the faulted phases are equal. E) N. A.
The fault current level of a circuit breaker used in a transmission line with phase voltage 4.6 kV and breaking capacity 50 MVA is . . kA.
Figure below shows the single-line diagram of three-bus power system with generation at bus 1 and bus 3. The voltage at bus 1 is V₁ = 1.025/0° per unit. The voltage magnitude at bus 3 is fixed at 1.05 per unit with a real power generation of 250 MW. The scheduled load on bus 2 is marked on the diagram. Line impedances are marked in per unit on a 100 MVA base. Line resistances and line charging susceptances are neglected. By using Gauss-Seidel method and initial estimates of V₂(0) = 1.020° and V3(0) = 1.0520°, determine V₂ and V3. Perform calculation for one iteration. V₁ = 1.025/0° j0.1 Slack Bus j0.2 j0.4 j0.2 3 j0.1 250 MW 150 Mvar |V3|=1.05 P3 = 250 MW
A hydro powered 50 MVA generator, with a synchronous reactance 0.33 p.u., delivers 40 MW over a transmission line of 0.15 p.u. reactance to an infinite system. A 3-phase short circuit transient fault occurs on the busbar between the generator and transmission line. Given that the generator emf is 1.4 p.u. prior to and during the fault and all reactances are to a 50 MVA base: Sketch the single line schematic diagram of the system. Determine the maximum load angle the generator can swing to without losing stability. i) ii) iii) iv) Sketch the corresponding power-angle curve for the system showing the accelerating and decelerating areas. Calculate the critical clearing angle of the system to keep its stability.
Consider the system shown in the single-line diagram of Figure (3). All reactances are shown in per unit to the same base. Assume that the voltage at both sources is 1 p.u. a Find the fault current due to a bolted- three-phase short circuit at bus 3 b- Find the fault current supplied by each generator and the voltage at each of the buses 1 and 2 under fault conditions 0.06 p.u. 0.2 p.u. 0.04 p.u. 0.25 p.u. 0.2 p.u. 0.2 p.. 0.2 p.u. 0.06 p.u. 0.25 p.u. Figure (3) Single-line diagram ele ver ele 888 ele 0.06 p.u. 0.25 p.u.
5) Non minimum phase systems are also non causal. ) True False
iv. The swing equation can be considered mathematically, as a equation due to the v. The main objects of fault analysis are term.
Write about the uses and importance of twisted pair cable - crossover cable
The % voltage drop is calculated for 3-phase systems by taking phase quantities and per phase line parameters True False
A. X B What logic gate has the same function as the circuit above?
1- Which of the following is true in decoupled load flow method a- Jacobians J1 and J2 are considered b-Jacobians J2 and J3 are considered c-Jacobians J2 and J3 are neglected d- Jacobians J1 and J2 are neglected 2-If all the three sequence currents at the fault point in a power system are equal, then the type of the fault is a.Line to line fault b.Three phase fault c.Double line to ground fault d.Single line to ground fault
In the shown below power system, both generators G1 and G2 emf’s are equal.All the system data are shown on the system diagram.a) Draw the system diagram in per unit using (MVA)base = 75 and (KV)base =20 KV in the generators side.b) Calculate the three-phase balanced short circuit current (If) at busbar 3 inAmpere and the fault level (MVA)sc in MVA.c) If the fault at busbar 3 is a line-to-line fault, calculate the fault current inAmpere and the fault level (MVA)sc in MVA.