Two tanks containing air with the given volume, mass, temperature and pressure shown in Figure Q2 are connected with the valve. Now the valve is opened and the air in the two tanks are allowed to mix and reach to equilibrium condition with the surrounding temperature of 20°C. Considering the necessary assumption determine, (a) the volume of tank B, (b) determine the pressure of both tanks after the valve is opened. (c) Can we use ideal gas low for saturated water steam at atmospheric pressure? Discuss the reason.

Two tanks containing air with the given volume, mass, temperature and pressure shown in Figure Q2 are connected with the valve. Now the valve is opened and the air in the two tanks are allowed to mix and reach to equilibrium condition with the surrounding temperature of 20°C. Considering the necessary assumption determine, (a) the volume of tank B, (b) determine the pressure of both tanks after the valve is opened. (c) Can we use ideal gas low for saturated water steam at atmospheric pressure? Discuss the reason.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Water is stored in a closed tank of capacity 0.1m3. The quality of water is 60% and initial pressure is 7 bar. Heat is transferred to the water until the tank contains only saturated vapour. At the end of this process, determine the mass of vapour in the tank, and the final pressure inside the tank.
Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains an indeal gas, and the other part is evacuated. The partition is then removed, and the gas expands into the entire tank. At the initial state, the mass of the gas is m= 4.00kg, initial pressure is p1 = 600.00 kPa, initial temperature is T1 = 300.00 K. The gas constant is R = 0.2870 kJ/(kg·K). (The internal energy can be determined by the equation ΔU=m·cv·(T2-T1), where cv = 0.7180 kJ/(kg·K) is the specific heat at the constant volume.) Calculate the final state temperature T2.__________ (K)
A 0.5-m3 rigid vessel initially contains saturated liquid–saturated vapor mixture of water at 120°C. The water is now heated until it reaches the critical state(point). Solve, 1. Show the process on T-v diagram with respect to saturation lines. 2. Determine the mass of the liquid water at the initial state.
A piston-cylinder device contains satuated water vapor with a constant pressure. The mass and the pressure are listed in the table below. The water is heated by a resistance heater (see the picture below) within the cylinder. The heat supplied by the heater is given in the table below. The cylinder is insulated so there is not heat loss. (a) Determine the enthalpy per unit mass after the water vapor received heat. (b) Determine the temparature after the water vaopr received heat. Parameter Pressure Mass of water Heat supplied by the heater Unit kPa g KJ Value 300 26 7.1 heater
Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part contains an indeal gas, and the other part is evacuated. The partition is then removed, and the gas expands into the entire tank. At the initial state, the mass of the gas is m= 4.00kg, initial pressure is p1 = 600.00 kPa, initial temperature is T1 = 300.00 K. The gas constant is R = 0.2870 kJ/(kg·K). (The internal energy can be determined by the equation ΔU=m·cv·(T2-T1), where cv = 0.7180 kJ/(kg·K) is the specific heat at the constant volume.) Calculate the final state pressure p2.__________ (kPa)
2) Two glass bulbs, one on the left with a volume of 2 liters and the other on the right with avolume of 6 liters, are connected to one another by a thin tube that is initially closed by astopcock. The bulb on the left has 0.1 moles of ideal gas, and the bulb on the right isevacuated. The system is in thermal equilibrium with the surroundings at 300K. When thestopcock is opened, the gas flows out to fill both bulbs. Calculate A for this process. If wewere to insert a propeller to extract work as the gas flows from left to right, what is themaximum amount of work that we could possibly extract?
Air as an ideal gas is contained in a piston/cylinder system constrained by a non-linear spring. Initially the gas in the cylinder is at 100 kPa, which is balanced by the atmospheric pressure outside of the cylinder (the weight of the piston is negligible). The force on the spring at the start is zero. The spring force is F=kx². k=600. kNt/m². The cross-sectional area of the piston is 1 m², the initial volume is 1 m³, and the initial temperature is 300 K. Heat is added until the volume of the gas has expanded to 1.5 m³. Find: (a) The work done by the gas on the face of the piston (kJ). (b) The final temperature (K). (c) The amount of heat added (kJ). Hint: This problem is easiest if you calculate the spring work and the atmospheric work separately. Air V₁=1.0 m³ Piston Area = 1.0 m² T₁=300 K P₁=100 kPa Atmospheric P on upper piston face= 100 kPa
X=6
I need the answer as soon as possible
The compression factor for low molecular-weight, real gases at very low pressure is,