In the PVT diagram, the term "dense fluid" is used to describe the material or fluid When it is in the solid region and the density starts increasing When it is around the critical point, whereby the material is more compressible than the liquid and denser than the vapour. When it is at the triple point, where the three phases exist at equilibrium When the material density remains unchanged

In the PVT diagram, the term "dense fluid" is used to describe the material or fluid When it is in the solid region and the density starts increasing When it is around the critical point, whereby the material is more compressible than the liquid and denser than the vapour. When it is at the triple point, where the three phases exist at equilibrium When the material density remains unchanged

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

An perfect gas of a specific composition At 10 g/mol, the molecular weight and specific heat ratio of this substance are equal. It has a pressure of 200kPa and an initial volume of 2m3 at this point. During the process of heat transfer, the pressure was more than doubled. Calculate the heat transfer if the process had 'n = infinity,' 'n = Cp/Cv,' and 'n = 3' parameters.
Determine the pressure of Gas 2. Follow the statement and the figure below. Apply Knowledge about Fluid Mechanics to solve the question.
Two liquids of different densities (= 1500 kg/m3 , = 650 kg/m3) are poured together in to a 100 – lit tank, filling it. If the resulting density of the mixture is 800 kg/m3, find the respective amounts of liquid used. Also, find the weight of the mixture; local g = 9.675 m/s2. (3 DECIMAL IN FINAL ANSWER PLS)
COMPLETE SOLUTIONS
A mixture of two liquids of equal volume is made, the one has a relative density of 0.8 and the other a density of 980kg/m³. What will be the weight of 2500 liters?
1. A sliding wire of length 3.5 cm is pulling a liquid film, as Figure 3 shows. The pulling force exerted by the wire is 4.4 x 10 N. From the table of surface tensions, determine the film material.
A 0.0856-m3 drum contains saturated water and saturated vapor at 360C. (a) Find the mass of each if their volumes are equal. What is the quality? (b) Find the volume occupied by each if their masses are equal.
A certain gas at 1 atm and 289 K, has a volume of 2.83M cubic centimeters are compressed into a storage vessel of 0.31 cubic meter capacity. Before admission, the vessel contained the gas at initial pressure of 138.7 kPa and 24 0C; after admission, the pressure increased to 1080.375 kPag. What should be the final temperature of the gas in the nearest Rankine?
2. Two liquids of different densities ( p, = 1,500 , Pz = 500) are poured together m3 m3 into a 100 liters tank filling it. If the resulting density of the mixture is 800 kg find the respective mass (kg) of the liquids used. TANK
A 0.71 cu.m tank contains 5 kg of an ideal gas. The gas has a molecular weight of 45 g/mol and is at 20 deg C. What is the gas pressure?
4. Supposing two liquids of different densities p kg 1200 and p kg 500- were poured 1 m m kg together inside a 100 L tank, filling it. If the resulting density of the mixture is 800, find the m respective quantities of liquids used. Also, find the weight of the mixture if the local m acceleration due to gravity is g = 8.675
Three liquids given the following properties are poured into the cylindrical container with a diameter of 3 meters and a height of 6 meters. First fluid poured: sg = 1.0, V = 17.6715 m^3 Second fluid poured: sg = 0.81, V = 10.6029 m^3 Third fluid poured: sg = 2.94 , V = 7.0686 m^3 Assuming that the container is closed after pouring the fluids and the stable state in the container is reached, determine the pressure at the height of 4-m from the bottom of the tank Select the correct response 7.9461 kPa 12.8084 kPa 28.8414 kPa 9.8100 kPa Assuming seawater to have a constant specific weight of 10.05 kN/m^3, what is the absolute pressure at a depth of 10 km. Select the correct response(s): 939 atm 339 atm 993 atm 399 atm