A rigid tank whose volume is unknown is divided into two parts by a partition. One side of the tank contains an ideal gas at 927 deg C. The other side is evacuated and has a volume twice the size of the part containing the gas. The partition is now removed, and the gas expands to fill the entire tank. Heat is now applied to the gas until the pressure equals the initial pressure. Determine the final temperature of the gas.

Q: Required information NOTE: This is a multi-part question. Once an answer is submitted, you will be…

A:

Q: Water is stored in a closed tank of capacity 0.1m. The quality of water is 60% and initial pressure…

A:

Q: Use the Ideal Gas Law to show how pressure and temperature are related in the case of two footballs…

A:

Q: Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition.…

A:

Q: 2. The piston is initially just touching the linear spring, and water is a compressed liquid. The…

A:

Q: A tank whose volume is unknown is divided into two parts by a partition. (Figure 1) One side…

A:

Q: B- A 1.8 m' rigid tank contains a refrigerant-134a at 50°C. One-third of the volum phase and the…

A: Given data⇒ The volume of the rigid tank - V=1.8 m3 Refrigerant - R-134a Temperature T=500C…

Q: A quantity of ideal gas with an initial condition of 0.1 m3 and 735 kPa expands isothermally to 118…

A:

Q: A rigid tank filled with R-134a is divided into two chambers by a membrane. The membrane is a…

A: As per our guidelines we are supposed to do only 3 subparts, kindly post other part separately.

Q: An ideal gas at 27 oC is heated at constant pressure till the volume becomes three times. The…

A:

Q: Using data from previous problem, if O.05 kg of gas leaks out of the tank and in the process the…

A:

Q: Q) Saturated (liquid+ vapor) ammonia at 60°C

A:

Q: piston cylinder arrangement contains 0.11 kg of Nitrogen and recieves 11.78 kJ of heat isothermally.…

A:

Q: Shown in the figure, an insulated rigid tank is divided into two equal parts by a partition.…

A: Giveninsulated tankm=4kgP1=600kPaT1=300KR=0.287 kJ/kgKCv=0.7180 kJ/kgK∆U=mCvT2-T1

Q: work against the piston. How much work is done during the process? How much error would be made by…

A: To determine the work done in the process and percentage error in the steam behaviour in ideal…

Q: For the situations below briefly explain how you obtained the values and provide the numerical…

A: It is required to determine properties for given process

Q: A piston-cylinder set up contains 0.015 kg of an ideal gas at a volume of 1 liter, a temperature of…

A:

Q: ii- The enthalpy of a perfect gas is equal the specific heat at constant pressure times th absolute…

A:

Q: Heating then continues until the pressure reaches 300 kPa. What is the volume, in L, at this…

A: ojjjjii

Q: . Determine its mass in kg.

A: To find mass in kg

Q: A rigid tank whose volume is unknown is divided into two parts by a partition. One side of the tank…

A: Given:The initial temperature of the ideal gas is T1=917°C.The initial pressure of the ideal gas is…

Q: At what maximum pressure must a be in order to contain water vapor at 10°C? system

A: Giventemperature of the water vapour is 10oC

Q: How did you determine the properties of water at state 3?

A: This question is based on the concept of Rankine cycle.

Q: Determine the mass of air in lbm when the pressure is 18.44 psi and the temperature is 80.8°F in a…

A: For solution refer below images.

Q: A spring-loaded piston-cylinder device contains   of carbon dioxide. Initially, the spring has no…

A:

Q: As shown in the figure below, you have a system including a Polyethylene vessel with mass Mvessel =…

A: Solution: Given Data: Mvessel=0.229 kgMwater=0.399…

Q: The 12" piston diameter is fitted into the cylinder shown in fig. A 0.3 lbm liquid-vapor mixture of…

A: Spring piston cylinder Construction and working Spring is connected to the piston and in cylinder…

Q: What is the difference between saturated liquid and compressed liquid?

A: Answer : Saturated liquid :- one can say when the liquid is about to vapourise Compressed liquid :-…

Q: system contains liquid water. Energy i

A:

Q: pressure is 20.45 psi and the temperature is 77°F in a closed chamber with dimensions 30.8 ft x 15.3…

A:

Q: A piston-cylinder contains 2.1 kg of air at T1 = 800 K and P1 = 848 kPa. The air is brought to a…

A:

Q: A rigid tank whose volume is unknown is divided into two parts by a partition. One side of the tank…

A:

Q: 2. An unknown gas (with PVT conditions of; 101 kPa, 2.83 m & 23°C) is to be transferred into a…

A:

Q: Determine the mass of air in lbm when the pressure is 19.21 psi and the temperature is 76.6°F in a…

A:

Q: re, an insulated rigid tank is divided into two equal parts by a partition. Initially, one part…

A: Given data as per question' Mass of gas, m=4 kgFor state 1P1=600 kPaT1=300KR=0.2870 kJ/kg K

Q: i) the final temperature of the refrigerant, °C, ii) the heat transfer to the refrigerant, kJ.

A: Given that: Cylinder volume =0.02 m3,  Refrigerant R-134a  Density of refrigerant = 85 kg/m3…

Q: A rigid tank (0.010 m³) contains saturated liquid water at 160 deg C. How much heat (kJ) must be…

A: The properties of the saturated liquid at 160 degrees Celsius are: The mass of the water inside the…

Q: An ideal gas expands from 11.5 cu.ft to 17.5 cu.ft at 85 deg.F and 15.5 psia. During the isobaric…

A:

Q: The dry saturated steam is expanded from 10 bar to 6 bar in a nozzle. If the expansion is…

A: The answer is in the next step

Work and Heat Transfer

It is generally related to thermal engineering which tells about the use, creation, conversion and transfer of heat energy between the systems. It is also considered that to transfer heat from one source to another, transfer of masses is also required. There are various mechanisms by which, transfer of heat takes place i.e. thermal conduction, convection, radiation or by change of phase. All these mechanisms have their own specific features which sometimes occur simultaneously within the same system.