Two solid cylindrical rods (1) and (2) are joined together at flange B and loaded, as shown. If the normal stress in each rod must be limited to 103 MPa, determine the minimum diameter required for each rod. Assume P = 62 kN and Q = 144 kN. di d2 (1) A ↑ B C Answers:

Q: Compare and contrast the uses of T-square and setsquares.

A: T-square: It is a technical instrument that is used for drawing purposes.  It is mainly used by…

Q: kindly resolve or recheck. thank you

A: Given data:

Q: 8. HSS 10 x 8 x1/4 with Fy-50 ksi is selected to be used as a compression member with KL=10ft.…

A: Since you have asked multiple question, we will solve the first question for you. If youwant any…

Q: Problem 6: A rigid bar, hinged at one end, is supported by two identical springs as shown. Each…

A: Solution:

Q: 3.) Consider the 2D frame shown below. There are pins at A, C, D. Point E is halfway between A and…

A: Find:

Q: g) At what single point along the beam does this maximum occur? h) What are the values of internal…

A:

Q: Label the maximum and minimum values on the graph. d) Draw the internal bending moment diagram (BMD)…

A:

Q: FIHD THe CENTROID (x $ Y) of THe GazOMETRY

A: Centroid is the point where the mass of whole body acts. If there is a figure which consists of…

Q: y 500 50 80 -140- - 140- 80 60 400 500 50 500

A: Given- plate area is given  To find- centroid of given plate area

Q: A well pumping test was carried out in an unconfined soil layer of thickness 15 m to determine its…

A: Given data in question  Unconfined aquifer  Discharge  Drawdowns Radius of influence  Total height…

Q: R = 100 N 30° 30° 15° 1.1 Determine the magnitudes of the components of force R on axes 1 and 2…

A: 1.1 Consider the given figure.

Q: A B с D Blocks A, B, and C have weights of Y N, 25 N, and 15 N, respectively. The coefficient of…

A:

Q: Draw the shear and moment diagram of the beam shown using area method. Identify the degree of the…

A:

Q: 3. Name any two-pattern material.

A: Introduction- There are several types of material found in nature. Some materials form certain…

Q: Please do parts d, e, and f.

A: Part d, e and f is to be solved

Q: Calculate the development length at simply supported edge in mm from the following information: M25…

A: Side way clear spacing is 50 mm,M25 and Fe 415 steelbd =1.4 MPaV = 30 KN and M = 16.076 KN-md = 120…

Q: Given the following information Distance Azimuth (m) Course Bearing Latitude Departure N 60°00' W…

A: Answer:- Latitude and Departure:

Q: .) Determine shear and moment equations of the beam shown. Neglect horizontal reactions since ther…

A:

Q: unit

A:

Q: a) top most, hef tmost

A: X = 1.5 cm Y = 5.48 cm

Q: Question 1 A vertical circular gate in a tunnel 8 m. in diameter has oil (0.80) on one side and air…

A: Solve letter A only Given- diameter d=8 m,air pressure P=40 kPa,oil height=12 m, Hydrostatic force=?

Q: Derive the expression

A: Expression for change in length of the block

Q: 4.) Consider the 2D beam supported by a pin at A and a roller at B. EXTERNAL FORCES a) Draw a FBD.…

A: Find:

Q: A simply supported wood beam with a span of L = 13 ft supports a uniformly distributed load w. The…

A:

Q: The pin-connected structure consists of two cold-rolled steel [E = 31,000 ksi] bars (1) and a bronze…

A: Calculate the area required for bar (2) so that each bar carries the same force.

Q: diagrams

A:

Q: A uniformly-distributed load w is supported by a structure consisting of rigid bar BDF and three…

A:

Q: Water at 60 °F is flowing from A to B in a 4-inch Sch. 40 steel pipe. Point B is 20.0 feet higher…

A: Given, D = 4 in  ∆z = 20 ft  L = 60 ft

Q: a AB shown.

A:

Q: Problem 12.16 Consider the building frame shown in (Eure) Suppose that My 2.6 k/ft and s8 k/ft.…

A:

Q: 5. An elastomeric bearing pad consisting of two steel plates bonded to a chloroprene elastomer (an…

A: Given  Dimensions a= 125 mm  b= 240 mm  t= 50 mm  Shear force, V= 12 KN

Q: For the frame shown, determine the reactions at the supports (support A is a hinged while B is a…

A:

Q: Crest vertical curve of 300m is connected with two tangents, where -1.0% grade is connected to a…

A: Data given Length of vertical curve = 300 m Grade, g1 =-1% Grade, g1 =-5% Elevation of PI = 177.000…

Q: Please do Part C, E, and F

A: To solve part C,E and F

Q: For the connection shown, the average shear stress in the 8-mm-diameter bolts must be limited to 158…

A:

Q: A horizontal bar of negligible mass is hinged at A and assumed to be rigid. It is supported by an…

A:

Q: Hydraulic Radius Determine the general expression for the hydraulic radius of a circular pipe…

A: It is asked to determine the expression for Hydraulic Radius of a circular pipe when it is fully…

Q: A W21x73 is supported on simple supports on a 30-ft span. Calculate the plastic moment Mp. Assume…

A: From Table, I=1600 in4 d=21.2 in y=d2=21.22=10.6 in MyI=fyyMy1600=5010.6My=7547.16 kip.in Yield…

Q: Water flows from a tank through 160 feet of 4 inches diameter pipe and then discharges into air as…

A: Given data,  n= 0.013 Discharge, Q= 12 cfs Length of pipe = 160 ft Diameter of pipe = 4 in To find…

Q: Problem III. Determine the support reactions at B and the location of the maximum deflection for the…

A:

Q: Dipper is another word for bucket. ) True False

A: A word or phrase that is exactly the same as another word or phrase in the same language. for…

Q: 3. A golf ball of mass 0.045 kg is hit off the tee at a speed of ball for 3.5x10-³s. Find (a) the…

A:

Q: Q. A saturated sand sample has dry unit weight of 20 kN/m³ and a wwwww specific gravity of 2.5. If…

A: Given - Weight of sand sample, Yd = 20 kN/m3 Specific gravity, G = 2.5 Yw = 10 kN/m3 To find -  What…

Q: A 1.30 in. diameter solid steel shaft supports loads PA = 55 Ib, Pc = 165 lb, and PE = 45 lb. Assume…

A:

Q: The rigid beam BC is supported by rods (1) and (2). The cross-sectional area of rod (1) is 12 mm2.…

A:

Q: Required to find: Tabulate the computed values accordingly. Length, Calculated Bearing LATITUDE…

A:

Q: A large crack was observed in a steel beam on a bridge. The bridge maintenance engineers drilled a 2…

A: Drilling : Drilling could be a saw during which a bit is employed to chop a spherical cross-section…

Q: do it correctly asap.

A: Given:-m1=1350kgm2=900kgnatural frequencies =4.91Hz and 12.05 HzTo find:-expressions for…

British Gravitational Bg System Of Units

Measuring is the comparison of a particular physical quantity with its reference value. A unit is a fixed physical quantity. The length is a physical quantity. A physical quantity is the product of a unit and the numerical value we need to compare with.