Crest vertical curve of 300m is connected with two tangents, where -1.0% grade is connected to a -5.0% grade tangent. Given the elevation of Pl is 177.000 m and the station of Pl is 0+150. Find the profile elevation of the vertical curve at 20 m interval. What is the profile elevation at chainage 0+200? . Also draw the curve profile. Use a graph paper or software.

Q: D В Bm 4m 3m A E G H 3m 3m 3m 3m 30KN 60KN 90KN

A:

Q: A double-angle shape is shown in Figure 3.5. The steel is A36, and th 4-inch-diameter bolts. Assume…

A:

Q: 30 kN 10 kN/m -2 m В 5m -3 m A

A:

Q: Same elevation - Water T-10°C Machine A

A:

Q: write the advantage and disadvantage of stiffness method and flexibility method

A: Answer The flexibility method is also known as the  Force method. The stiffness method is also known…

Q: Example : The following bearing of the lines observed for closed tränverse ABCDA with the surveyor…

A:

Q: The top curve of the window is a parabola that opens horizontally with its vertex at the lower right…

A:

Q: Determine the values of a for which the system has no solutions, exactly one solution, or infinitely…

A: Hello dear this is the solution of your problem Please see the attached solution, thanks

Q: Problem 5: Draw shear and bending moment diagrams and sketch the qualitative deflected shape for the…

A: A beam system is given in the figure belowNeed to Find Draw the shear force and bending moment…

Q: A 20 m long horizontal concrete floor under a barrage on a permeable foundation retains a 5 m head…

A: Given-Length L=20 m,Head =5 m,5 m deep downstream end pile.Calculate the exit gradient.

Q: A B F C D 000 4₁ L₂ L3 Fishing line with a tensile strength of 50 lbs is used at B to fasten 2…

A: Tensile strength of fishing line (T) = 50 lbs Determine the maximum force F that can be supported.

Q: The framework shown in Figure 1 is supported by an A-ball joint and an E-roller. Neglecting the…

A:

Q: 1. Compute the magnitude of the designated quantities by using their corresponding influence lines.…

A:

Q: 8.129 The rectangular plate is subjected to the pressure P Po-cos 2b Determine the resultant force…

A: It is required to calculate the resultant force of pressure and co-ordinates of point of…

Q: Problem Two: Consider the cross-sectional shown in the figure below. The cross-section is reinforced…

A:

Q: A W12x14 supports distributed dead and live loads over a simple span. wD 0.8 kip/ft, wL 0.3 kip/ft L…

A:

Q: 4. For the truss shown, determine the forces in members AB, BG, ED and GF 6 kN 2.4m B 24m C 24 m D…

A:

Q: (5) This simply-supported beam has been subjected to an applied moment at midspan. The M(x)…

A:

Q: The thin uniform plate shown has a mass of 100 kg and is subjected to a force and couple moment…

A:

Q: In a 2 dimensional stress analysis, the state of stress at a point is shown below in which length of…

A:

Q: Determine the x and y-coordinate of the centroid shown below

A:

Q: Force Method is also know as Method of Answer Displacement

A: methods of analysis of indeterminate structure is  done by following methods - 1) Force method /…

Q: Conjugated beam

A: The given beam is simply supported with an overhang. A point load is acting at the free end of the…

Q: The tension member shown in the figure below is a ¹/2 x 10 plate of A36 steel: Fy = 36 ksi, Fu = 58…

A:

Q: Find the Normal Stress at points A, B, and C in the Rod below. Dimensions given are diameters. 1 in.…

A:

Q: Explain the uses of Mohr’s circle to determine stresses.

A: The equations of transformation for plane stress may be represented by a plot in graphical form…

Q: A simple concrete beam (300 mm x 500 mm) is subjected to a uniform loading of 10 kN/m throughout its…

A: The given figure is shown below:

Q: e. Hinge Hinge Hinge

A:

Q: Conjugate-Beam Method

A: We find the reaction from total area as area gives total load.

Q: A beam with the cross section is bent about vertical axis. Assume that the yield stress, oy is…

A:

Q: A steel bar 2 m long, 20 mm wide and 15 mm thick is subjected to a tensile load of 30 kN. If…

A:

Q: 3.50. Annual floods for a stream have a normal frequency distribution. The 2-year flood is 40,000…

A: Floods are among Earth's generally normal and most disastrous regular dangers. A flood happens when…

Q: Determine the estimated endurance strength in MPa to 1 decimal place for a hot rolled steel 17 mm…

A:

Q: Determine planar support reactions as well as normal force, shear force, and bending moment…

A:

Q: 50 kN 100 kN 50 kN E D F 1m A B 2 at 2m = 4m EA = constant - 120 GDa

A:

Q: Solve the force in members DF, DG and CE of the truss shown in the figure using method of joints. 9'…

A: Given truss with loading conditions and it is asked to determine the force in the members DF, DG and…

Q: Problem 3c.1 The bar ABC is pinned at 4 and there is a roller support at B. The bar has a…

A:

Q: A 1.75 m Area = 800 mm² B 1.25 m C Area = 500 mm² 75 kN 1.5 m D 50 kN P.

A: Determine the deformation of point b in mm

Q: 1. Determine the slope at A and the maximum displacement of the beam. Take E = 29(103)ksi, I = 500…

A:

Electronic Spreadsheet

Tabular listing has many advantages ranging from time management to efficient scheduling of tasks. Electronic spreadsheets allow the user to tabulate and analyze data, using its easy-to-use interface. An electronic spreadsheet is a staple application used among accountants, management staff, and IT professionals. It is used in various sectors worldwide for data management. An electronic spreadsheet is a system and computer software that could be used to do numerical computations automatically. Spreadsheet application programs are often organized as a table with rows and columns. Each row and column intersect to form a cell, which may be used to store data. These data can take the form of a written label, a number, or a formula that combines information from other cells.