Two plates of thickness 16 mm and 14mm are required to be joined by a butt (groove) weld. The plates are subjected to a factored tensile force of 400 KN. The effective weld length is limited to 180 mm. Check whether the joint is safe if in following cases? (Assume f= 250 N/mm²) (a) Single Vbutt weld is provided (b) Double Vbutt weld is provided

Two plates of thickness 16 mm and 14mm are required to be joined by a butt (groove) weld. The plates are subjected to a factored tensile force of 400 KN. The effective weld length is limited to 180 mm. Check whether the joint is safe if in following cases? (Assume f= 250 N/mm²) (a) Single Vbutt weld is provided (b) Double Vbutt weld is provided

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Two steel plates, each 400mm wide and 12mm thick, are to be joined together by a lap splice (single). The electrode to be used for the weld has a nominal tensile strength of 550Mpa. Determine the following:a. the maximum weld size that can be usedb. effective net area of the fillet weld using the maximum weld size allowed by the manualc. the maximum load that can be resisted by the weld using the maximum weld size allowed by the manual.
Please Use LRFD * ASD!
* 2. Calculation question: Two side fillet welding joint, N=660 kN (static loading, design value), using angle steel with 2L 110×10. The thickness of gusset plate is t1=12 mm, using the steel of Q235B and electrode of E43, SMA welding. Determine the leg size hf and actual lengths of two welds. 300 N 2L110×10 t=12 110
If the structural frame is replaced to structural steel and the connections is to be designed, determine the following Determine the centroid of the weld measured from the given origin A. Determine the direct shear load in the welds. Determine the required size of the fillet weld(E60xx) if the maximum resultant load is 750,000 N/mm
See the image. Two steel plates are welded together. The thickness of the bottom plate is 10mm and the thickness of the top plate is 8mm. What is the maximum and minimum sizes of the weld.
Using SMAW process, E70 electrodes and an A572 steel. Determine thelength of the side fillet welds for the full capacity the 125x100x10mm angle tensionmember as shown below. Assume that the member is subjected to repeatedstress variations making any connection eccentricity undesirable. Check theblock shear strength of the member. Assume that the WT chord has sufficientstrength to develop the weld strengths and the thickness of its web is 12mm. UseU = 0.87 for class use and LRFD Method only.
Topic:Welded Connection - Civil Engineering -Steel Design *Use latest NSCP/NSCP 2015 formula to solve this problem *Please use hand written to solve this problem A plate is attached to the frame of a machine by side fillet welds as shown in the figure. Determine the size of the welds to resist a vertical load of 150 kN. Assume that the allowable shearing stress at the throats of the weld is 145 MPa.
Assume that the gusset plate and welds are satisfied. A gap allowance of 1/16 inch is to be considered to fit the gusset plate in the HSS. The steel used in the tension member is ASTM A500 Grade C HSS 6 x 0.5 with a length of 30 feet. a.) Find the shear lag factor b.) Find the Effective net area (Ae) c.) Solve for the tensile strenngth 16-inch-long fillet weld HSS 6 x 0.5 1/2 in. thick gusset plate 17 inch long
In an industrial shade on edge support consisting of two angle 110 mm x 100 mm is to be connected to a 16 mm gusset plate for a tensile load of 650 kN. Design the moment free welded connection. The distances of centroid of angle from the back side of legs are C₁=C₁ = 30.9 mm. The strength of the weld per mm thickness per mm length is 76 MPa.
A tension member splice is made with 14-inch E70 fillet welds as shown in Figure 5. Each side of the splice is welded as shown. All steel is A36. Determine the maximum service load, P, that can be applied if the live load to dead load ratio is 1.5. Note: Assume that the base metal shear strength is adequate (check the yielding strength for the gross area, fracture strength for the effective net area, weld strength and block shear strength). PL 5/8x8 4 in. Figure 5 2 PL 7/16x4