Two different options A and B with brake pads for disc brakes are connected to the rope drum. The diameter of the rope drum is 150 mm. What distance must the pads B be at from the center of rotation to cover the same distance as A?A B- Width 50 mm - Width 60 mm- Evidence center 120mm - Construction power 900 N from rotation center.- Maintains a weight of 200 kgwhen the installation force is 1.4kN (μ is missing from the data)M=μF(Ry-Ri)Right answer R=187 mm

Two different options A and B with brake pads for disc brakes are connected to the rope drum. The diameter of the rope drum is 150 mm. What distance must the pads B be at from the center of rotation to cover the same distance as A?A B- Width 50 mm - Width 60 mm- Evidence center 120mm - Construction power 900 N from rotation center.- Maintains a weight of 200 kgwhen the installation force is 1.4kN (μ is missing from the data)M=μF(Ry-Ri)Right answer R=187 mm

International Edition---engineering Mechanics: Statics, 4th Edition

4th Edition

ISBN:9781305501607

Author:Andrew Pytel And Jaan Kiusalaas

Publisher:Andrew Pytel And Jaan Kiusalaas

Chapter7: Dry Friction

Section: Chapter Questions

Problem 7.60P: The force P applied to the brake handle enables the band brake to reduce the angular speed of a...

See similar textbooks

Similar questions

i need the answer quickly
A single block brake, as shown, has a tangential braking force of 2000 N and normal force 6000 N pressing on the brake block on the wheel. Which of the following is the force P required to operate the brake? 600 P -Brake drum 200 IF 50 100 10 1850 N 1625 N 1375 N 2150 N RN
Q2/ Arm ABC acts as a brake on the wheel as shown in Fig. 2. The coefficient of static friction at B is pB = 0.4. Determine the largest moment M that can act on the wheel without causing it to slip? Radius = 200 mm 100 N M 300 шn O B Figure 2 400 mm A 200 mm
When stopping a car on an icy or wet road... or a dry road, for that matter... is it better to push the brake pedal hard enough to lock the wheels and make them slide? Or to push gently so that the wheels continue to roll? What is the point behind "anti-lock disk brakes"? Which coefficient of friction u, or uk is relevant to which case? (hint: start by considering the forces on different points on the wheel in each case, and calculate the largest possible deceleration for both conditions)
Each problem requires a proper FBD and separate kinematic diagram. 1. The wheel has a weight of 20 lb and a radius of gyration of kg = 0.75 ft. If the coefficients of static and kinetic friction between the wheel and the surface are 4 = 0.5 and 4 = 0.35, find the greatest angle, 0 , that the slope can have without the wheel slipping. 1.25 ft-
Form the figure shown, a flexible belt placed around a rotating drum of 4-inch radius acts as a brake when the arm ABCD is pulled down by the force P. The coefficient of kinetic friction between the belt and the drum is 0.7. What force P that would result in a braking torque of 400 lb . in., assuming that the drum is rotating Neglect the weight of the counterclockwise. brake arm. 60° 4 in. 60° A B C -2 in.²4in. 2 in. 42×-| -2 D P
A lever brake system is used to keep a wheel with an applied moment from moving. If the coefficient of static friction is Hs = 0.35 and the dimensions are as given in the parameter table, find the minimum force P that will keep the wheel from moving. BI A Mo value units parameter L1 L2 L3 400 mm 390 mm 30 mm r 140 mm Мо 450 N-m Р-
The figure below shows the essential parts of a hydraulic brake system. The area of the piston in the master cylinder is 1.8 cm² and that of the piston in the brake cylinder is 6.4 cm2. The coefficient of friction between shoe and wheel drum is 0.50. If the wheel has a radius of 37 cm, determine the frictional torque about the axle when a force of 50 N is exerted on the brake pedal. N. m Wheel drum Pedal Shoe Master cylinder cylinder Brake
A single block brake, as shown, has a tangential braking force of 500 N and normal force 1500 N pressing on the brake block on the wheel. The drum diameter is 240 mm. Which of the following is the force P required to operate the brake? -200 * 200 P 184 0 775 N O 725 N O 1000 N O690N
Dont copy from chegg The disc brakes at the front of a car have pistons of 1582 mm2 cross-sectional area each, whereas the drum brakes at each of the rear wheels have pistons of 300 mm2cross-sectional area. The master cylinder has piston of 582 mm2 cross-sectional area.Determine the total force applied at the front and rear brake cylinders and the ratio in
Please solve this question in handwritting. Again in handwriting
A band brake embraces a drum of 0.41 m diameter such that one end of the band is attached to the fulcrum pin and the other end is attached to a pin B as shown. The operating force P is 120 N and the coefficient of friction between the band and the drum is 0.27. Determine the braking torque that the band brake provides in Nm. P 75 -450 TO с 270° T₂ All dimensions in mm.