Two bolts are used to form a joint connecting rectangular bars in tension as shown. If the bolts have a diameter of 11.2mm and the load is P = 99KN, determine the average shear stress (in MPa) on the bolt surfaces that are subjected to direct shear. Note: Do NOT include units in your answer

Two bolts are used to form a joint connecting rectangular bars in tension as shown. If the bolts have a diameter of 11.2mm and the load is P = 99KN, determine the average shear stress (in MPa) on the bolt surfaces that are subjected to direct shear. Note: Do NOT include units in your answer

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

What is the shear stress developed on the UPPER spring (in MPa)? What is the shear stress developed on the LOWER spring (in MPa)? What will the total elongation of the spring (in mm)? indicate the free body diagram
Two steel springs arranged as shown support a load P. The left spring consists of 12 turns of 20-mm diameter wire on a mean diameter of 300 mm. The right spring has 10 turns of 16-mm diameter wire on a mean diameter of 200 mm. Calculate the maximum value of P and the total elongation if the allowable shearing stress is 200 MPa. Us the Exact formula. Answer: P = 1443.35 N
PROBLEM No.1 If the wood joint shown in the figure has width of 200 mm, determine the average shear stress developed along shear planes a - a and b - 6. 8KN 8KN 125 mm 150 mm
Two hard rubber blocks (G- 334 kPa) are used in an antivibration mount to support a small machine, as shown. Determine the shear strain in the blocks if the applied load P-456 N. Assume a - 20 mm, b- 50 mm, and c-80 mm. Note: Do not include units in your answer Answer:
The sanding-drum mandrel shown in the figure is made for use with a hand drill. The mandrel is made from a rubber-like material that expands when the nut is tightened to secure the sanding sleeve placed over the outside surface. If the diameter D of the mandrel increases from 1.95 in. to 2.05 in. as the nut is tightened, determine (a) the average normal strain along a diameter of the mandrel. (b) the circumferential strain at the outside surface of the mandrel. Sanding sleeve D - Mandrel Answers: (a) ED = i in./in. (b) Ec= in./in.
The solid steel rod (1) has an allowable shear stress of 12 ksi. The brass tube (2) has an allowable shear stress of 5 ksi. The diameter of the rod is d1 = 0.625 in. The outside diameter of the tube is D2 = 1.625 in., and its wall thickness is t2 = 0.125 in. The tube is attached to a fixed plate at C, and both the rod and the tube are welded to a rigid end plate at B. Determine the largest torque Tmax that can be applied at the upper end of the steel rod.
200 mm 1.36 The bell crank, which is in equilibrium under the forces shown in the figure, is supported by a 20-mm-diameter pin at D that is in double shear. Determine (a) the required diameter of the connecting rod AB, given that its tensile working stress is 100 MPa; and (b) the shear stress in the pin. -240 mm- 50 mm 10° 60° FIG. P1.36 30 kN 150 mm- FIG. P1.37 50 mm
The normal strain in a suspended bar of material of varying cross section due to its own weight is given by the expression yy/3E where y = 3.0 lb/in.³ is the specific weight of the material, y = 6.3 in. is the distance from the free (i.e., bottom) end of the bar, L = 21 in. is the length of the bar, and E = 27000 ksi is a material constant. Determine, (a) the change in length of the bar due to its own weight. (b) the average normal strain over the length L of the bar (c) the maximum normal strain in the bar. Answer: (a) d = i (b) avg (c) Emax i x10-6 in. με με
Consider the pre-deformation cross-section of a bar, a side view of which is shown in the figure below. The diameter of the bar is d 180 mm. A bending moment is applied that causes the neutral axis to become concave up. What is the normal strain h = 30 mm from the bottom of the bar if the radius of curvature is measured to be p Express your answer to three significant figures. ▶ View Available Hint(s) £= - ΠΙΑΣΦ vec ? Ax mm/mm 5.4 m?
Using hooks law determine strain if modulus of elasticity=78 MPa, and stress-23 MPa
Need help with this