Transform the set of cartesian strain components (, = 400 µe (y = 250 µe „ = 125 pe %3D %3D 7ay = 275 µe %3D Yy: = 175 pe Yex = 225 ue into a new set of cartesian strain components relative to an Ox'y'z' set of coordinates, where the direction angles associated with the Ox'y'z' axes are n/3 R/3 y 3n/4 R/4 1/3 n/3 In/4

Q: It is a widely use tool for laying out squaring and checking work.It consists is a square head and a…

A: following is the answer to the above question-

Q: Q.6) Complete the following table: No. Part of vernier calliper 1 Main Scale Vernier Scale 3 Screw

A: The main scale reading is that to the left of the zero on the vernier scale. The vernier reading…

Q: 49. Which of the objects seen above would be the best choice to be completely machined on a lathe?…

A: Given:Find:49) The objects seen above would be the best choice to be completely machined on a…

Q: 2 Major parts of the lathe 2 Types of the lathe 5 Types of lathe cutting tools 4 principal parts of…

A: given; major parts of the lathe types of the lathe types of the lathe cutting tool

Q: 44. Bigger diameter end mill cutting tool is preferred during milling operation. Select one: True O…

A: In general, milling is a machining process in which the rotary motion of the cutter is used to…

Q: the reading of this tool is

A:

Q: Up milling operation is performed for finishing cut. Select one: True O False

A: Down milling is performed for finishing and get smooth surface.

Q: 9. To produce the line of intersection between the two cylinders, connect the project points using a…

A: Since we only solve up to three subparts, we will answer the first three. Please resubmit the…

Q: Q3) A student wants to know the linear measurements of a screw thread (in inch), if the student…

A: (A) The thread angle is 55o (B) The screw type is the "Whitworth screw"

Q: The grinding wheel is made of aluminium oxide are bonded with cobalt. Select one: O True O False

A: Grinding wheel: It is a wheel composed of abrasive compound and it is used for various grinding and…

Q: Metric thread of 0.8 mm pitch is to be cut on a lathe. Pitch of the lead screw is 1.5 mm. If the…

A: The speed of rotation of the lead screw is 800 rpm.

Q: v thread is:

A: In screw largest diameter is its major diameter

Q: If a spur gear has a pitch of 18 teeth per inch and 29 countable teeth, what is the diameter of that…

A: Pitch, P= 18 teeth per inch Number of teeth, T= 29   To find: Diameter of the gear in inches, D

Q: This a sketch of what process. V, F Punch Flash Die Cutting edges Select one: a. Cutting O b.…

A: The given sketch represents Trimming process. Trimming process: The shearing of the excess material…

Q: just to clarifay is the shaft stainless steel? or the tool making the threads on the shaft

A: It is the shaft which is made up of stainless steel.

Q: Name the milling machine operation in which the dovetail grooves can be produced in the workpiece.…

A:

Q: Match each of the following terms to the phrase that describes it. Answers are used only once.

A: The correct match is: Drill spot           -     3Countersink      -     6Knurl                  -…

Q: Given a gear of 24 teeth, 4 diametral pitch. Calculate the following giving results to 3 decimal…

A: As per our guidelines we are supposed to solve only 3 subparts if multiple subparts are asked .…

Q: he process of machining the start of a drilled hole to make a conical shape or angle is known as:…

A: Given: In this question multiple choice is given so we will learn about them one by one

Q: Triangular files are commonly used for filing corners between 60° and 90° Select one: O True O False

A: Triangular files were initially made for trimming saw tooths and gear tooths as the triangular cross…

Q: 17, 18, 19, 20. A gear wheel of 34 teeth has to be milled by simple indexing n each tooth, the index…

A:

Q: Why it is important to loosen one screw before tightening the opposing one by an equal amount?

A: If there are two sequences of screws or bolts and n number of screws is to be tightened on each…

Q: 1. Determine the tolerance allowed on the hole of the part.

A: Tolerance – the total allowable change in measurement; the contrast between the upper and lower…

Q: Write 10 steps of the Procedure for internal thread cutting

A: 1) Hole is first bored to the root diameter of the thread. 2) Tool is fixed on the tool post or on…

Q: (3) You are to produce a machine part (a shaft) with different diameters S0mm.35mm and 30mm with…

A: Machining is a material removal process in which materal is removed by using cutting tools to obtain…

Q: 46. During the drill operations, the work piece and drill bit make an angle of 450. Select one: O…

A: Drilling is a cutting operation which uses drill bit to cut a circular hole in solid materials.

Q: The deep drawing blankholder is used in order to avoid defects of the flange which are named O a.…

A: b. The deep drawing blank holder is used to avoid wrinkling defect

Q: In charpy test specimen, the angle of v-notch section is_- O a. 60 degrees O b. 30 degrees O c. 90…

A: In the Charpy test, we measure the toughness of the material.  The angle of the V notch is 45 degree…

Q: (8 10 6, 11 22 23 24 2 25 12 13 (6 (14.

A: given: name the part of lathe machine?

Q: The maximum safe compressive stress in a hardened steel punch is limited to 1 GPa and the punch is…

A:

Q: Note 1 indicates 10 GAGE 1010-1020 sheet metal can be used to make the main body of this part…

A: Tolerance is the difference between the maximum size and the minimum size of the part or element.

Q: Sally is making a sine bar, which is used to machine angles on parts (see the given figure). She has…

A:

Q: In drilling operations, drill chucks are used for holding the work piece. Select one: True False

A: The above statement is false

Q: What is tapping

A: Handwriting.jpg

Q: Double cut files use a second set of teeth,perpendicular to the first set to produce a rougher…

A: The given statement is “Double cut files use a second set of teeth perpendicular to the first set to…

Q: is the lathe operation, which is performed without the cutting tool moving parallel to the axis of…

A: Lathe is a machine tool which is used in the work shop to perform the various machining operations…

Q: Using the Brown & Sharpe dividing head with the above standard gears and the differential indexing…

A: Brown and Sharpe is the name of the scientist who discovered the concept of head indexing. Indexing…

Q: the main diference between the prick punch and center punch?

A: Prick punch is a mechanical tool, which is made up of steel and it is used to mark points on the…

Q: In which lathe operation enlarging the already drilled hole can be produced. Boring operation…

A: Correct Option: Boring Operation.

Q: Pitch characteristics

A: pitch characteristic When viewed in a cross-sectional plane containing the axis of the thread, the…