Topic: MOMENT DISTRIBUTION METHOD Question: draw and completely compute the moment distribution method tabulation, the shear diagram and the moment diagram of the given load diagram below INSTRUCTIONS IN ANSWERING: 1. Consider clockwise moment is positive and counterclockwise moment is negative. 2. Use only up to three (3) cycles 3. Use two (2) decimal places in all your answers 4. Stiffness factor (K) and distribution factor (DF) must be expressed in fraction. JOINT MEMBER K DF FEM₁ DM₁ COM₂ DM₂ COMS DMS EM R R V R 5m AB 10 m 30 KN 40 kN/m BA BC 8m 10 KN 2m CB

Topic: MOMENT DISTRIBUTION METHOD Question: draw and completely compute the moment distribution method tabulation, the shear diagram and the moment diagram of the given load diagram below INSTRUCTIONS IN ANSWERING: 1. Consider clockwise moment is positive and counterclockwise moment is negative. 2. Use only up to three (3) cycles 3. Use two (2) decimal places in all your answers 4. Stiffness factor (K) and distribution factor (DF) must be expressed in fraction. JOINT MEMBER K DF FEM₁ DM₁ COM₂ DM₂ COMS DMS EM R R V R 5m AB 10 m 30 KN 40 kN/m BA BC 8m 10 KN 2m CB

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

For the forces acting on the beam shown in Figure 3.1f, determine the location of the equivalent resultant force with reference to point A in m. Given / = 2.4, P1 = 8, P2 = 8 and w = 2 %3D (Note: Prefix the answer with negative sign "." if the location is to the left of the reference point. E.g. if the location of the equivalent resultant is located between points A and B, or to the left of point B by 1.2m, the answer should be "-1.2" with reference to point B) P, kN W kN/m P, kN C 21 m 21 m Figure 3.1f
Answer the following and write on a clean paper written then box your final answer.
Using any of the three Geometric Methods, answer the following beam. Indicate the negative sign (-) if the answer is downward.
Solve the problem by the moment-area method. The beam has constant flexural rigidity EI. A simple beam AB supports two concentrated loads P at the positions shown in the figure. B C 4. 4 A support C at the midpoint of the beam is positioned at distance d below the beam before the loads are applied. Assuming that d = 12 mm, L = 5.4 m, E = 200 GPa, and I = 193 x 10° mm, calculate the magnitude of the loads P (in kN) so that the beam just touches the support at C. 163.87 x kN
Beam AB is loadead as shown. If P is 1000 lb, Solve for the ff: • Horizontal support reaction at A and B • Vertical support reaction at A and B Include 4 decimal points in all answers.
Problem 1: A nonuniform beam is simply supported at both ends. The flexural rigidity of the left part equals EI, whereas the flexural rigidity of the second part equals (s+1)EI where's'is your serial number. (a) Use K functions to derive the characteristic equation; (b) Solve for the characteristic equation to derive natural frequencies. Report the results. (s+4)EI EI L/2 SERIAL NUMBER= 2
Question Can Please Help Me: Structural Theory/Civil Engineering 60 minutes only the given time. Wish you could help me. I will give UPVOTE and GOOD FEEDBACK.
A 6.6m cantilever beam shown carries 189KN/m uniform load. Point A is free end while point B is fixed support. Using Double Integration Method with origin at point A, calculate the second constant of integration, C2 in KN-m³. Express your answer in 2 decimal places. A W - L B
problem 9
SOLVE THE FOLLOWING PROBLEM AND SHOW YOUR COMPLETE SOLUTIONS. EXPLAIN YOUR ANSWER FOR BETTER UNDERSTANDING.
answer the following given problem, show complete solution and fill all the boxes in the tabulation, solve using moment distribution method , show shear and moment diagrams. ASAP
The distributed load value shown in the figure affects the unit length. Calculate the internal forces at the given angle value for θ. (θ =120)