INSTRUCTIONS 1) Consider clockwise moment is positive and counterclockwise moment is negative. 2) Use only up to three (3) cycles 3) Use two (2) decimal places in all your answers 4) Stiffness factor (K) and distribution factor (DF) must be expressed in fraction. IN ANSWERING: JOINT MEMBER K DF FEM₁ DM₁ COM₂ DM₂ COM3 DM3 EM RL RF V R ///////////// AB 10 kN/m 6m BA BC 8 m 15 KN 4 m /////////// с CB

INSTRUCTIONS 1) Consider clockwise moment is positive and counterclockwise moment is negative. 2) Use only up to three (3) cycles 3) Use two (2) decimal places in all your answers 4) Stiffness factor (K) and distribution factor (DF) must be expressed in fraction. IN ANSWERING: JOINT MEMBER K DF FEM₁ DM₁ COM₂ DM₂ COM3 DM3 EM RL RF V R ///////////// AB 10 kN/m 6m BA BC 8 m 15 KN 4 m /////////// с CB

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Using Conjugate Beam Method: The simply supported beam carries loads as shown in the figure below. Compute the following:a. Slope θAb. Slope θBc. Slope θCd. Deflection ΔBe. Maximum deflectionEI is constant; E = 200GPa and I = 5x10^6 mm^4
Problem 2: Using the matrix stiffness method, determine the displacement at the point of application of the 20 kip load, all unknown nodal displacements, and use the results of your analysis to draw the shear and moment diagrams. 71 zok W EI = 1x10 8 Koin 2 00 5k
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=4.50 m, b=5.00 m, c= 2.75 m, P = 33kN and M = 195kN-m. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise. 1.Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) (in kN) 2.Determine the shear force acting at each of the following locations: (in kN)(a) x = 4.50- (i.e., just to the left of point B)(b) x = 4.50+ (i.e., just to the right of point B)(c) x = 9.50- (i.e., just to the left of point C)(d) x = 9.50+ (i.e., just to the right of point C)Note that x = 0 at support A. 3. Determine the bending-moment…
red is the correct answer
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=2.50 m, b=4.75 m, PB = 45kN, and PC = 90kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.
Use discontinuity functions to develop the load function w(x) for the beam shown. Include the beam reactions in this expression. Integrate w(x) twice to determine V(x) and M(x), and use these functions to plot the shear-force and bending-moment diagrams on paper. Use these plots to answer the questions in the subsequent parts of this GO exercise. Let a = 2.75 m, b = 4.00 m, c=1.75 m, Wg = 20 kN/m and wc = 55 kN/m. WC WR b Calculate the reaction forces A, and Dy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since A, = 0, it has been omitted from the free-body diagram.) WC y A B C A D |Dy Incorrect Use your shear-force equation V(x) to find the location where V= 0 between points B and C. Alternatively, note that the shear force at B in this case is known from Part 3. Recall that the change in the shear force between any two locations is equal to the area under the distributed-load curve…
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=6.0 ft, b=24.0 ft, P = 38 kips and w = 6.5 kips/ft. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.Calculate the reaction forces Ay and Cy acting on the beam. Positive values for the reactions are indicated by the directions of the red arrows shown on the free-body diagram below. (Note: Since Ax = 0, it has been omitted from the free-body diagram.) Determine the shear force acting at each of the following locations:(a) x = 6.0- ft (i.e., just to the left of point B)(b) x = 6.0+ ft (i.e., just to the right of point B)(c) x = 28.0 ftNote that x = 0 at support A. When entering your answers, use the shear-force sign convention detailed in Section 7.2.Answers: (a) V = kips (b) V =…
Determine the following unknowns on the beam shown below using DOUBLE INTEGRATION METHOD. Consider 150mm x 150mm section and E = 200 GPa. Show complete and organized solution. Solve the following: - Deflection at point B - Deflection at point E - Slope of the elastic curve at point D in degrees.
Use virtual work method. Find vertical displacement of joint B in mm due to external force only
For the simply supported beam subjected to the loading shown, derive equations for the shear force V and the bending moment M for any location in the beam. (Place the origin at point A.) Let a=2.250 m, b=6.50 m, PA = 60kN, and PC = 70kN. Construct the shear-force and bending-moment diagrams on paper and use the results to answer the questions in the subsequent parts of this GO exercise.
please solve correctlt
An indeterminate beam carries different types of loads as shown in the figure. Using Moment Distribution Method (up to 4th distribution), solve the following: Let w = 295KN/m (NOTE: Put a negative sign if the moment is CCW otherwise don't put any sign at all. Don't also put any units. Express ALL YOUR FINAL ANSWERS to at least 5decimal places) 9w 3w 3m 5m 4m Solve the distribution factor of member CB. Solve the distribution factor of member ВА. Solve the 1st carry over moment of span АВ.