Calculate the vertical deflection of point C, and also the horizontal displacement of the rollersupport at point E using the Principle of Virtual Work (that is two separate problems). For beamvertical deflection, use expressions for M(x) and M'(x) to calculate the Wr. Check that answer byusing the integration tables. For horizontal displacement of point E, use the integration tablesonly. Modulus of Elasticity = 29,000 ksi.5.0 kip10 ftBIbeam = 533 in“12 ftIcolumns = 350 inE20 ft

Answered: Image /qna-images/answer/3e10ace7-0392-4470-a330-9f4e6c34ddcd.jpg

Answered: Calculate the vertical defle support at…

Calculate the vertical defle support at point E using the vertical deflection, use exp using the integration tables only. Modulus of Elasticity

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Problem II. An exhaust gas piping fabricated as shown is subjected to a bending moment, an internal pressure, and a torque. In points A and B, the following stresses occur due to the loading: o 63.5 MPa, B=127 MPa, = 127 MPa A.B A.B a. Determine Gmin, omax, and its direction (in degrees) from x-axis at point A. b. Determine omin, omax, and its direction (in degrees) from x-axis at point B. 1 B d O A x
A square beam (w=0.03 m) is loaded with a point load of 1000 N and a moment load of 1000 Nm, as shown. i. Determine maximum deflection of the beam using step by step analytical equations. ii. Determine the Maximum stress in the beam using step by step analytical equations iii. For both top fibers and bottom fibers of the square beam, specify the type of the stresses.
AW410 x 60 standard steel shape is used to support the loads shown on the beam in the figure. Assume P = 130 kN, w = 27 kN/m, a = 2.8 m, and b = 2.0m. Determine the magnitude and location of the maximum bending stress in the beam. A max = x = a i i B a → Pin |C * b W MPa m D a E
PROBLEM 01: Hollow bar length is 1.40m long and tube length is three-fourth as long as the bar. Torque T=1100N.m acts at the free end of the bar. Both the bar and tube are made of an aluminum alloy with shear modulus of w ww elasticity G=27GN/m². Given that dl=35mm, d2=45mm, d3=60mm, d4=70mm. Determine the following: a. Maximum shear stress in both the bar and tube b. Angle of twist at the end A of the bar. (In degrees) Tube Fixed plate End plate Tube d3 d1 d2 d4 Bar Cross-section of the bar and tube
Calculation: Modulus of Rupture: 3PmaxL MR = 2bh² Apparent Modulus of Elasticity: PL³ E = (4) 4bh³ Pmax and L = maximum load and span of the beam b and h = width and height of the cross-section P = increment of applied load below proportional limit A = increment of deflection of beam's neutral axis measured at midspan over distance L and corresponding load P Note: The weight of the beam is not included in the above calculation. Where:
Determine the design moment capacity of the cross section by answering the sub-problems given below. The relevant cross section and material properties are given below. Given Properties (a) Determine if the beam is over- or underreinforced. Double check your estimation by referring to Table A.4. (b) Given the answer of problem (a), draw the stress and strain distributions of the RC cross section at ultimate load. Use the rectangular stress block to describe the compression stress. Denote key stress/strain values using symbols. (c) Formulate the equilibrium equation. Also find the undetermined value . (d) Determine the nominal and design moment capacity, and .
A rectangular plate is subjected to uniform biaxial stress with x = 90 MPa (tension), oy = -20 MPa (compression), and ₂ = 0. The plate has original dimensions 400 X 800 X 200 mm (x X y X z) and is made of steel with E = 200 GPa and v = 0.3. What are the strains Ex, Ey, and Ez?
A reinforced concrete beam is shown in the figure below. 0.75-in, diameter rods Wo 20 in. 2.5 in. 8 ft- 8 ft 10 in. Part A Determine the maximum uniform distributed load wn that can be supported by the reinforced concrete beam if the allowable tensile stress for the steel is (Ost )allow = 30 ksi and the allowable compressive stress for the concrete is (oconc )allow = 3 ksi . Assume the concrete cannot support a tensile stress. Take Est = 29(10) ksi , Econe = 3.6(103) ksi Express your answer to three significant figures.
Write A if only the first statement is true. B if only second statement is true. C if both statement is correct. D if both statement is false 1. The bulk modulus of elasticity is a property that relates changes in pressure to changes in volume. It is dimensionless number. 2. Adhesion of water to the walls to the vessel will cause an upward force on the liqiud at the edges and result in a meniscus which turns upward. This also referred to as capillary action.
Two vertical forces, each of magnitude P= 20 kips, are applied to a beam of the cross section shown. Determine the maximum tensile and compressive stresses in portion BC of the beam. 3 in. 3 in. 3 in. A 40 in. P -60 in. P 6 in. 2 in. 1 40 in. D The maximum tensile stress is The maximum compressive stress is required.) ksi. (Round the final answer to two decimal places.) ksi. (Round the final answer to two decimal places. Include a minus sign in the answer if
A rectangular concrete beam measures 300 mm wide and has an effective depth of 450 mm. Compression steel consisting of two No.22 bars is located 60 mm from the compression face of the beam. If f= 35 MPa and fy = 420 MPa, what is the design moment capacity of the beam for the tensile steel area As = four No. 36 bars in two layers? Provide material properties for concrete and reinforcing steel used in your design.
A small aluminum alloy [E = 73 GPa] teeshape is used as a simply supported beam as shown. For this beam, a = 150 mm. The cross- sectional dimensions of the teeshape are b = 25 mm, d= 38 mm, and t=7 mm. After loads are applied to the beam at B, C, and D, a compressive normal strain of 490cis measured from a strain gage located at c= 9 rmm below the topmost edge of the tee stem at section 1-1. What is the applied load P? 3P Strain gage d a a H Answer: P = i