A symmetrical beam of length I has a cantilever support at the left hand end x = 0 and a pin support at the right hand end x = L 112 = F ( 212 + ¹¹2 - L) 2L The bending moment along the beam is given by: My (x): Given the following values, find the value of w the displacement in the z direction at the mid-point of the beam. F = 282 N L 1,224 mm Iy = 2,154 mm4 E 101 GPa Enter your answer as an integer, in mm, but without the units.

A symmetrical beam of length I has a cantilever support at the left hand end x = 0 and a pin support at the right hand end x = L 112 = F ( 212 + ¹¹2 - L) 2L The bending moment along the beam is given by: My (x): Given the following values, find the value of w the displacement in the z direction at the mid-point of the beam. F = 282 N L 1,224 mm Iy = 2,154 mm4 E 101 GPa Enter your answer as an integer, in mm, but without the units.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

A truss is loaded as shown in the figure. Assume AE = 10000
There is a wooden beam AD, as shown in the figure below, the Flexural Rigidity of the beam section is constant EI: Q:Try to find the (vertical) displacement of point B after deformation.
3. A beam is loaded and supported as shown in the figure. The beam has a constant value of EI. Determine: a) The reaction at supports A and B b) The equation of the elastic curve for segment AC. c) The equation of the elastic curve for segment CB. d) The deflection at the middle of the span (point C) (Check your answer: deflection at C = McL2/32EI downward) Mc L B
The cantilever beam consists of a rectangular structural steel tube shape [E = 29,000 ksi; / = 1930 in.41. For the loading shown, determine: (a) the beam deflection at point A (b) the beam deflection at point B. Assume MA = 250 kip-ft, P = 29 kips, LAB = 4.9 ft, LBc = 7.4 ft.
Please see the image below. Thank you
The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.36 in^2. Find the elongation (in inches) of rod AC caused by the 3530-lb load if x = 9ft and theta = 51.8 degrees. Use E = 29167 ksi for steel. Note: Round off the final answer to four decimal places.
Pls solve A and B
QUESTION 03 A beam ABCD is supported and loaded as shown in Figure Q3. The flexural rigidity, El is constant. By using Macaulay's method, and take point A as origin, determine the: (a) Reactions at all supports A, C and D. (b) Deflection at point B (c) Slope at support A 1 m 1 m 1 m 2 kN/m 4 kNm Figure Q3/ Rajah S3
The rigid bar BC is supported by the steel rod AC of cross-sectional area 0.27 in2. Find the vertical displacement (in inches and absolute value) of point C caused by the 2448-lb load if x = 9.5 ft and θ = 41.7ᵒ. Use E = 29147 ksi for steel. Note: Round off the final answer to four decimal places.
9.3-17 The beam shown in the figure has a guided suppot at A and a roller support at B. The guided support permits vertical movement but no rotation. Derive the equation of the deflec- tion curve and determine the deflection ô, at end A and also dc at point C due to the uniform load of intensity q PIL applied over segment CB and load P at x = L/3. (Note: Use the second order differential equation of the deflection curve.)
The beam ABC is subjected to a point load at the middle of segment AB and a uniformly distributed load at the segment BC, as shown in the figure. A 20 N Set Wo B 1.5W, N/m Figure 1: Overhang beam Find the equation of the elastic curve for the segment AB. L C - 3 N/m, L = 2 m, EI = 25000 Nm². Use the method of superposition for all parts. Hint: for x > L/2 in segment AB, the solution can be obtained from the table by replacing x by L-x.
The beam is subjected to a shear of V= 2 kN. What is the average shear stress developed in each nail? if the nails are spaced 75 mm apart on each side of the beam. Each nail has a diameter of 4 mm. The N.A is located on 137.5 mm form the bottom of cross section. The second moment of inertia about N.A is 63.5417*10^(-6) m^4. 75 mm 50 mm 75 mm 200 mm 25 mm 200 mm 25 mm 442.62 MPa