: tire with 700 kPa air pressure distributes a load over an area with a circular contact radius, a, of 130mm. The pavement was constructed with a material that has a modules of elasticity of 345000 kPa and a Poisson ratio of 0.45 and thickness of 30cm. Calculate the rudial-horizontal stress and deflection at a point the pavement surface under the center of the tire load. Also, calculate the radial-horizontal stress and deflection at a point at a depth of half pavement layer way from the centre of the tire load. (USE: Ahlvin and Ulery equations).

: tire with 700 kPa air pressure distributes a load over an area with a circular contact radius, a, of 130mm. The pavement was constructed with a material that has a modules of elasticity of 345000 kPa and a Poisson ratio of 0.45 and thickness of 30cm. Calculate the rudial-horizontal stress and deflection at a point the pavement surface under the center of the tire load. Also, calculate the radial-horizontal stress and deflection at a point at a depth of half pavement layer way from the centre of the tire load. (USE: Ahlvin and Ulery equations).

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

17. In the Asphalt Institute flexible pavement design approach, Where are the critical stress and strain locations checked?a. Top of the asphalt concrete layerb. Middle of the asphalt concrete layerc. Bottom of the asphalt concrete layerd. Bottom of the asphalt concrete layer and top of the subgrade
Every information is correct. Please do it correctly or let other experts do it. Don't reject A tyre with 230 kPa air pressure distributes a load over an area with circular contact radius of 200 mm. The pavement was constructed with a material that has a modulus of elasticity of 450 MPa and a Poisson's ratio of 0.40. 1.1 Calculate the radial-horizo talking stress and deflection at a point on the pavement surface under the center of the tyre load. [Function values table: A 1 B-0 C-O R-0.5 H=2]
The rigid pavement (slab), due to its higher stiffness as characterized by elastic modulus, usually distributes the loading across a large pavement area. A. True B. False
The following figure shows concrete pavement with the layer thickness and elastic modulus as indicated. Assume modulus of rupture of 650 psi, load transfer coefficient of 3.2, serviceability loss from 4.5 to 2.5, and drainage coefficient of 0.9. The bedrock depth and loss of support is not considered for the subgrade. Use the design equation or monograph with 50% reliability to solve the following: 1) Determine the number of ESAL that the pavement can carry before failure. 2) If the daily traffic has 1080 single axles (20-kip), 400 single axles (24-kip), and 680 tandem axles (40-kip), and the annul traffic is the same over the design period, how many years would the concrete pavement last before failure? 8-inch Portland Cement Concrete Ec=4×106 psi 8-inch Granular Subbase Ec=30,000 psi Subgrade Mr = 5000 psi
A dual wheel having a load per tire of 4000 Ib, 80 psi pressure and μ = 0.5. Calculate thetotal pavement deflections due to the dual wheel by two layer theory at the followingradial distances from the centerline of one tire: r=0, 7,14. Assume that E1 = 10 E2
3. a) What is meant by dowel bar? Why it is used in the rigid pavement? b) Design the Dowel Bars for the following parameters: i) Design wheel load = 5100 kg ii) Design load transfer 40% iii) Slab thickness 30 cm iv) Joint width = 2.0 cm v) Modulus of dowel support = 42000 kg/em3 vi) Modulus of elasticity of dowel bar = 2x106 kg/cm2 vii) Modulus of subgrade reaction = 8 %3D viii) Grade of concrete = M 50
A cement concrete pavement of a certain thickness laid over a sub grade has a radius of relative stiffness 85 cm. If the thickness of the pavement were to be doubled, what would be the percentage reduction in the flexural stress by the Westergaard's corner load formula under wheel load P. Given that the area of the tyre contact (assumed circular) is 1540 sq. Cm.
Calculate the equivalent radius of the contact area of tires considering the wheel load is 60 kN.Allowable bearing pressure on the base of the pavement is approximately 0.20 MPa and thethickness of pavement is calculated as 160 mm. Round up the answer in 10 mm interval.
Calculate the equivalent radius of the contact area of tires considering the wheel load is 60 kN.Allowable bearing pressure on the base of the pavement is approximately 0.20 MPa and thethickness of pavement is calculated as 160 mm. Round up the answer in 10 mm interval
. Design the thickness at the edge and at the center of rigid pavement of the proposed ABCD Road to carry a wheel load of 7500 kg. Allowable tensile stress of concrete is 0.065f'. Assume f'c = 20 MPa.
A rigid pavement is to be used to carry a wheel load of 51.13 kN. Enough dowels will be used across the joint. What will be the difference in thickness (in mm) between the edge and the center of the pavement? The allowable tensile strength of concrete is 1.32 Mpa
A rigid pavement has a wheel load capacity of 53.96 kN. The allowable tensile stress of concrete is 1.37 MPa. Determine the thickness (cm) of the pavement if dowels are negligible. Express your answer in 1 decimal place.