A cement concrete pavement of a certain thickness laid over a sub grade has a radius of relative stiffness 85 cm. If the thickness of the pavement were to be doubled, what would be the percentage reduction in the flexural stress by the Westergaard's corner load formula under wheel load P. Given that the area of the tyre contact (assumed circular) is 1540 sq. Cm.

A cement concrete pavement of a certain thickness laid over a sub grade has a radius of relative stiffness 85 cm. If the thickness of the pavement were to be doubled, what would be the percentage reduction in the flexural stress by the Westergaard's corner load formula under wheel load P. Given that the area of the tyre contact (assumed circular) is 1540 sq. Cm.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

choose True or false Q1A- Initial tangent modulus is given by the slope of a line drawn tangent to the stress-strain curve at any point on the curve. * True False B- Plastic shrinkage of concrete is higher at a larger cement content. * True False C- Dynamic modulus of elasticity of concrete is approximately taken as equal to the secant modulus of elasticity of concrete * True False
17. In the Asphalt Institute flexible pavement design approach, Where are the critical stress and strain locations checked?a. Top of the asphalt concrete layerb. Middle of the asphalt concrete layerc. Bottom of the asphalt concrete layerd. Bottom of the asphalt concrete layer and top of the subgrade
Every information is correct. Please do it correctly or let other experts do it. Don't reject A tyre with 230 kPa air pressure distributes a load over an area with circular contact radius of 200 mm. The pavement was constructed with a material that has a modulus of elasticity of 450 MPa and a Poisson's ratio of 0.40. 1.1 Calculate the radial-horizo talking stress and deflection at a point on the pavement surface under the center of the tyre load. [Function values table: A 1 B-0 C-O R-0.5 H=2]
The rigid pavement (slab), due to its higher stiffness as characterized by elastic modulus, usually distributes the loading across a large pavement area. A. True B. False
Q3/Choose the correct answer 1. In general PSI for flexible pavement depend on............ Va. Cracking, Patching and Rutting b. Cracking and Patching c. Patching and Rutting d. Rutting 2. The Maximum contraction joint spacing for plain jointed concrete pavement is C. 3.5 m b. 4.5 m c. 5.5 m d. Depends on traffic load 3. The relationship between A psi and age of pavement is...... a. A psi co age Apsi ∞ (1/age) c. A psi 02(1/age) d. Non of the above 4. The surface of the pavement should be a. Smooth b. Rough 5. Which type of aggregates gives good workability? a. Round b. Flaky c. Angular 6. Rutting may be avoided by a. Good compaction . Sufficient enough to resist skid b. Good drainage 7. Bleeding may be avoided by a. Water voids b. Air voids c. Asphalt type 12. Tie bars in cement concrete pavements are at a. Expansion joints d. All the above acceptable c. High filler percent All the above 8. The good drainage in pavement can La Increase the pavement life b. Decrease the pavement life…
3. a) What is meant by dowel bar? Why it is used in the rigid pavement? b) Design the Dowel Bars for the following parameters: i) Design wheel load = 5100 kg ii) Design load transfer 40% iii) Slab thickness 30 cm iv) Joint width = 2.0 cm v) Modulus of dowel support = 42000 kg/em3 vi) Modulus of elasticity of dowel bar = 2x106 kg/cm2 vii) Modulus of subgrade reaction = 8 %3D viii) Grade of concrete = M 50
Calculate the design thickness in mm (rounded to the nearest tens) at the center of a rigid pavement with dowels if the: Allowable tensile strength of concrete = 3.0 MPa Wheel load = 117 kN
A concrete slab to be used for a given runway used by a design aircraft 727-200 dual – wheel gear of 150000 Ib gross weight. The 90- day flexural strength of concrete is found to be 800 psi. The modulus of subgrade reaction is 200 pci, and the annual equivalent departures were expected to be 15000. The required thickness of concrete runway slab to carry the design aircraft is ................. in.
Asaap
A pavement element along Thika road of 100x150x200 mm was subjected to an equalall round pressure of 120kn/m2 and axial load of 2.5KN in the X-direction. The changesin length are 0.92mm in X-direction, 0.27mm in the Y-direction and 0.18mm in the Z direction. Calculate thei. Elastic theory ratio, Eii. Poisson’s ratio,iii. Bulk Modulus, K
A rigid pavement is to be used to carry a wheel load of 51.13 kN. Enough dowels will be used across the joint. What will be the difference in thickness (in mm) between the edge and the center of the pavement? The allowable tensile strength of concrete is 1.32 Mpa
8. A rigid pavement concrete slab is shown in the given figure. Determine the stress and also max. deflection due to corner loading h 10 in. k = 100 pci h 10 in, a = 6 in. 9. Repeat problem (8) for interior loading case as shown in the given figure: S k= 100 pci h = 10 in. k = 100 pci a = 6 in. a 6in. 10,000 lb %i 4₁ 10,000 lb 10. Repeat problem (3) for edge loading cases (Circular or semi circular) as shown in the given figure: 110,000 lb %c = ? D. ? e = ? = ? 11. A section of a highway with length of 10 Km was evaluated using the Pavement Condition Rating Methods. The existing distresses along with this section are presented in the given photos. The severity and extent levels of each distress are given with the photo of the specified distress. The PCR form rating is also given.