Three wheel loads roll as a unit across a 60-ft span. The loads are P1 = 15000 lb and P2 = 9000 lb separated by 9 ft, and P3 = 6000 lb at 18 ft from P2. Determine the maximum moment and maximum shear in the simply supported span.

Three wheel loads roll as a unit across a 60-ft span. The loads are P1 = 15000 lb and P2 = 9000 lb separated by 9 ft, and P3 = 6000 lb at 18 ft from P2. Determine the maximum moment and maximum shear in the simply supported span.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three moving loads of P1, P2 and P3 have fixed distances apart. Distance between P1 and P2 is d1 while distance between P2 and P3 is d2. . These loads passes thru a 20 m length beam. This beam is supported at point B (roller) and point C (hinged) with distances of 10 m and 20 meters from leftmost end of the beam (point A). Point D is located midway of points B and C. Given data: P1 = 40 kN, P2 = 60 kN, P3 = 80 kN, d1 = 2 m and d2 = 2 m. Which of the following most nearly gives the maximum negative moment at D in kN-m caused by the moving loads.
R
12. Determine the reactions R₁, R₂, R3, and R4 using Three Moment Equation. Provide free body diagram of the spans. R₁ 100 lb/ft 10 ft R₂ 5 ft -160 lb/ft 400 lb R₂ 5 ft 3 ft- MATHaling.co 400 lb 6 ft 3 ft R4
A cantilever beam, 9 meters long. partially carries a uniform load of 60 kN/m at midspan, 6 meter from the fixed support. Use Unit Work Load Method to answer the following questions. 60 kN/m A B C 3 m 6 m 19. What would be the value of the moment, M, in terms of the distance x on the span on the span BC considering the uniform load? (Hint: required to find is the value of M in the unit load method at span BC) а. — 3(х — 3) b.-3(x – 3)? с. (х — 3) d. 0 20. What would be the value of the virtual moment, m, in terms of the distance x on the span where the uniform load lies if 1 unit load is applied at B?
12 kN/m -6 m- For the 6-m-span structural steel IPE 220 beam and loading shown in the left figure, maximum moment is Mmax = 54 kN m. Calculate the B flexural stresses at the uppermost and lowermost surfaces indicating whether in tension or compression.
The beam is subjected to a service dead load of 2.5k/ft for the entire length and a service live load of 20 kips at 4 ft from left end. The self weight of the beam b = 12in h=24 in has to be added to the dead load for the calculations. How much is the reaction for the design load at point A and paint B?
A straight cantilever of uniform cross-section carries a total load W distributed evenly over its entire length. If the free end of the cantilever is now propped upto the level of the fixed end, the vertical force required at the prop is
3..
A simply supported span (middle span) of 6-m length with double cantilever of 1.5 m at each end is loaded as shown below. There is a concentrated moment of 6 kN-m acting at the tip of the left cantilever and a point load of 3 kN acting at the tip of the right cantilever. A concentrated force P = 10 kN is acting at the mid-point of the middle span. In addition, there are two partial uniform load of 5 kN/m acting on the middle span as shown below. The middle span has an I-section, of which the value of the moment of inertia I is given. The dimensions of the two flanges and the vertical web are also given. The right cantilever has a T-section. The dimensions of the top flange and the web are given. P = 10 kN 5 kN/m A B 3 kN 200 mm 5 kN/m 200 mm 6 kN-m S mm S mm 10 mm 2 m 1 m 2 m B 250 mm 250 mm 1.5 m 6 m 1.5 m S mm Section A-A **- 10 mm Section B-B left cantilever middle span right cantilever I= 6.67 x 10 ^7 mm^4 a.) Calculate the maximum bending stress of the middle span and plot the…
= 3. A rectangular beam having b = 10 in. and d= 17.5 in. spans 15 ft face to face of simple supports. It is reinforced for flexure with three No. 9 bars that continue uninterrupted to the ends of the span. It is to carry service dead load D = 1.27 kips/ft (including self-weight) and service live load L 3.70 kips/ft, both uniformly distributed along the span. Design the shear reinforcement, using No. 3 vertical U stirrups. The more approximate Eq. (5.12d) for Vê may be used. Material strengths are f = 4000 psi and f₁ = 60,000 psi. Sketch your web reinforcement design for the half length of beam. (10pt) Wul 2 (Hint: Wu = 1.2wd +1.6w₁ = 7.44 klf. Consequently, Vu at the end of beam shall be where l is the length of beam)
2. Three wheel loads roll as a unit across a 35-ft span. The loads are Wi = 4000 lb and W2 = 8000 lb separated by 9 ft and W3 = 6000 lb at 27 ft from Pj. Determine the maximum moment and maximum shear in the simply supported span.
For the beam shown below, determine the maximum positive bending moment at point D due to the wheel loads of the moving HS15-44 truck shown. Hinge B Hinge. C D 4 m 4m 6 m 6 m -3 m--3 m- 48 kN 48 kN 12 kN 4 m 2.8 m