A truck with ultimate axle loads of 40kN and 60kN on a wheel base of 5m rolls across a 10m span simply supported T-beam of a bridge. In addition to the traffic load, the beam supports WDL 15.25kN/m and WLL-14.063kN/m. Determine the number of 28 mm diameter bars to adequately support the maximum moment in the beam. Use f'c-21MPa, fy=415MPa, stirrups diameter 10mm, and concrete cover=40mm. 600 mm 100 mm As B 300 mm 10 m mum 500 mm

Q: A propped cantilever made of a prismatic steel beam is subjected to a concentrated load P at mid…

A:

Q: A steel beam is made up of a wide flange section whose total depth is 600mm, width of the flange is…

A: Please refer and use given formula in above question M =wL28 + PL4 M = 40 × 928 + 200 × 94 M = 855…

Q: Wmax IP FL/3 L/2 と The simply-supported beam shown supports a load [P] at [L/3] from the right-hand…

A:

Q: 0.25 m DE 0.25 m 1.5 m F D 10° 60° 30° L 0.5 m 2m J A HW18: FBD of the bucket and whole upper…

A:

Q: P2 Examination Questionnaire.odf - Nitro Pro 10 CLOUD HELP Situation 2 | Beam ABCDEFG below is…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: If the allowable bending stress for the built-up section is 60% of the yield strength, Fy, Determine…

A:

Q: P A B C D -L/3- L/2- L/2- PROBLEM 9.58 For the beam and loading shown, determine (a) the reaction at…

A: EI = constantDeterminea. The support reaction at A. b. The deflection at midpoint C.

Q: HW-4/ For the girder floor beam system shown, find the maximum bending moment at section (1) of…

A:

Q: A reinforced concrete floor system consists of a 3-in. concrete slab supported by continuous-span…

A: The given figure is shown below:

Q: A three member frame consists of a vertical member AB. Sm long and horizontal members BC and CD each…

A:

Q: ity in kip-ft of a W27*336 steel beam having an unbraced length of 10 ft. Use ASD

A: Properties of W27×336 Ix=14600 in4 Iy=1180 in4 rx=12.1in ry=3.45in zx=1130 in3 zy=252 in3 unbraced…

Q: A reinforced concrete beam is 225 x 650 mm (bxd). The tension steel consists of 2H16 and 2H20 bars…

A:

Q: A rigid beam ABC supports a linear distributed load with maximum value q while supported by a pin at…

A:

Q: S.7-1: A cantilevered HSS 2x2x3/16 tube beam is 2 ft long and supports a sign from the side of a…

A: Given Section : 2*2*3/16 weight = 800 lb

Q: A tractor weighing 3000 lb with a wheel base of 9 ft, carries 1800 of its load on the rear wheels.…

A: Given data:- Weight of tractor is 3000 lb Wheel base is 9 ft Load on rear wheels, PR=1800 lb The…

Q: Verify that the size of the simply supported plate girder

A: plate girder is a steel beam that is widely used in bridge construction.Explanation:It is made by…

Q: Your roll no. kN 30kN/m B1 4 m 2 m Re

A: Given Overhanging beam and asked to draw SF and BM

Q: A rectangular beam has a width of 300 mm and an effective depth of 440 mm. It is reinforced with…

A:

Q: A column was designed with 200UC46.2. The length of the column is 4500 mm and both ends can be…

A:

Q: Determine the following if f'c=21 MPa and f(subscript)y3= 415 MPa a.) balanced steel ratio b.)…

A: Given - F'c =21MPa Fy = 415 MPa

Beams

In structural engineering, a beam is a component made of a variety of materials (including steel alloys, and wood) that can resist loads applied laterally to the beam axis. Members, elements, rafters, shafts, and purlins are all terms used to describe beams.