Note:hand written solution should be avoided. =Verify that the size of the simply supported plate girder(web height - 2200 mm, web thickness 8 mm, flangewidth 500 mm, and flange thickness - 25 mm) with aspan of 16m is sufficient to support the maximummoment produced due to a factored UDL of 75kN/mincluding self-weight. The compression flange is laterallysupported at the ends and at mid-span. Take C₁ valueequal to 1. Steel is A36.

plate girder is a steel beam that is widely used in bridge construction.Explanation:It is made by…

Answered: Verify that the size of the simply…

Engineering

Civil Engineering

Verify that the size of the simply supported plate girder

Steel Design (Activate Learning with these NEW titles from Engineering!)

6th Edition

ISBN:9781337094740

Author:Segui, William T.

Publisher:Segui, William T.

Chapter10: Plate Girders

Section: Chapter Questions

Problem 10.7.8P

See similar textbooks

Related questions

Q: Please recalculate and maksure everything above is correct. thanks

A: Steps to solve this question:Assumptions and sign conventions of forces and reactions.Find the…

Q: ASTM C188 Give three significance and uses of ASTM C188

A: ASTM - American Society for Testing and Materials. The code ASTM C 188 is used to determine the…

Q: A. WATER LINES, PIPES, CONNECTIONS AND FIXTURES B. SEWER LINES, PIPES, CONNECTIONS AND FIXTURES…

A: Hi! Thank you for the question As per the honor code, We’ll answer the first question since the…

Q: Define Dynamic Replacement.

A: Dynamic Replacement is the dynamic compaction variation, and comprises of delivering energy of…

Q: name three requirements contained in the specifications regarding material

A: A specification often refers to a set of document requirements to be satisfied by a material or…

Q: M1 Apply the terminology used in construction technology to a given building construction project.

A: Brief Concept Introduction- Concrete Technology- Concrete technology is concerned with the study of…

Q: What is specific gravity (sp gr)

A: Given data in question Specific gravity To be discussed What is specific gravity Specific…

Q: Solve thee following problem step by step so I can understand in neat hand writing.

Q: Distinguish between web buckling & web crippling

A: Web buckling and web crippling are two different failure modes that can occur in structural members,…

Concept explainers

Steel Framing

A steel frame consists of a skeleton frame structure comprising of horizontal I-beams and vertical steel columns fitted in a rectangular grid building construction to brace the floors, walls, and the roof of the building held onto the frame. Due to the implementation of this methodology, the construction of the skyscrapers was feasible.

Question

Note:hand written solution should be avoided.

=
Verify that the size of the simply supported plate girder
(web height - 2200 mm, web thickness 8 mm, flange
width 500 mm, and flange thickness - 25 mm) with a
span of 16m is sufficient to support the maximum
moment produced due to a factored UDL of 75kN/m
including self-weight. The compression flange is laterally
supported at the ends and at mid-span. Take C₁ value
equal to 1. Steel is A36.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1: Given data

VIEW

Step 2: Calculation the self weight of the plate girder

VIEW

Step 3: shear stress

VIEW

Step 4: bending stress

VIEW

Solution

VIEW

Step by step

Solved in 5 steps with 11 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

A plate girder must be designed for the conditions shown in Figure P10.7-4. The given loads are factored, and the uniformly distributed load includes a conservative estimate of the girder weight. Lateral support is provided at the ands and at the load points. Use LRFD for that following: a. Select the, flange and web dimensions so that intermediate stiffeners will he required. Use Fy=50 ksi and a total depth of 50 inches. Bearing stiffeners will be used at the ends and at the load points, but do not proportion them. b. Determine the locations of the intermediate stiffeners, but do not proportion them.
A W1422 acts compositely with a 4-inch-thick floor slab whose effective width b is 90 inches. The beams are spaced at 7 feet 6 inches, and the span length is 30 feet. The superimposed loads are as follows: construction load = 20 psf, partition load = 10 psf, weight of ceiling and light fixtures = 5 psf, and live load = 60 psf, A992 steel is used, and fc=4 ksi. Determine whether the flexural strength is adequate. a. Use LRFD. b. Use ASD.
A column in a building is subjected to the following load effects: 9 kips compression from dead load 5 kips compression from roof live load 6 kips compression from snow 7 kips compression from 3 inches of rain accumulated on the roof 8 kips compression from wind a. If lead and resistance factor design is used, determine the factored load (required strength) to be used in the design of the column. Which AISC load combination controls? b. What is the required design strength of the Column? c. What is the required nominal strength of the column for a resistance factor of 0.90? d. If allowable strength design is used, determine the required load capacity (required strength) to be used in the design of the column. Which AISC load combination controls? e. What is the required nominal strength of the column for a safety factor of 1.67?
Determine the smallest value of yield stress Fy, for which a W-, M-, or S-shape from Part 1 of the Manual will become slender. To which shapes does this value apply? What conclusion can you draw from your answer?
A beam must be designed to the following specifications: Span length = 35 ft Beam spacing = 10 ft 2-in. deck with 3 in. of lightweight concrete fill (wc=115 pcf) for a total depth of t=5 in. Total weight of deck and slab = 51 psf Construction load = 20 psf Partition load = 20 psf Miscellaneous dead load = 10 psf Live load = 80 psf Fy=50 ksi, fc=4 ksi Assume continuous lateral support and use LRFD. a. Design a noncomposite beam. Compute the total deflection (there is no limit to be checked). b. Design a composite beam and specify the size and number of stud anchors required. Assume one stud at each beam location. Compute the maximum total deflection as follows: 1. Use the transformed section. 2. Use the lower-bound moment of inertia.
The frame shown in Figure P4.7-8 is unbraced, and bending is about the x-axis of the members. All beams areW1835, and all columns areW1054. a. Determine the effective length factor Kx for column AB. Do not consider the stiffness reduction factor. b. Determine the effective length factor Kx for column BC. Do not consider the stiffness reduction factor. c. If Fy=50 ksi, is the stiffness reduction factor applicable to these columns?
Compute the nominal shear strength of an M107.5 of A572 Grad 65 steel.
Compute the nominal shear strength of an M1211.8 of A572 Grade 65 steel.
The given beam is laterally supported at the ends and at the 1 3 points (points 1, 2, 3, and 4). The concentrated load is a service live load. Use Fy=50 ksi and select a W-shape. Do not check deflections. a. Use LRFD. b. Use ASD.