-40 ft- -60 ft- -14 ft-30 ft- 4 k 16 k 16 k 5. For the bridge beam shown, determine the shear at point B of the beam due to the wheel loads when the front axle of the truck is located at a distance of 16 ft from the left support A.

-40 ft- -60 ft- -14 ft-30 ft- 4 k 16 k 16 k 5. For the bridge beam shown, determine the shear at point B of the beam due to the wheel loads when the front axle of the truck is located at a distance of 16 ft from the left support A.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: 6-65. Determine the horizontal and vertical components of force that pins A and B exert on the…

A: Given : Determine the horizontal and vertical component of reaction at A and B ?

Q: Problem 004-mj The truss pinned to the floor at D, and supported by a roller at point A is loaded as…

Q: D. -3 ft- 300 lb

Q: 6.32

Q: A continuous beam has a loading shown. Assuming constant flexural rigidity (EI). 50KN 35KN 70KN 40KN…

Q: A steel girder is part of highway 251A bridge in OK. Inspection reports have indicated that some…

Q: Determine the Maximum positive moment (kN-m) in the beam shown Where: P = 84kN; w= 10kN/m; L1 = 3m;…

A: Differentiate equation with respect to x acix to obtain bending moment location.

Q: A simply supported beam is supported at both ends. E 200 GPa,1- 60 x 106 mm. It has a span of 12 m.…

Q: Problem IV. Refer to the beam shown below. Internal hinges are installed at points C and E. Given:…

Q: H.W No1 Determine the resultant force and Specify where it acts on the beam measured from point a…

A: Thank you for the question . As per honour code we will answer the first question since the exact…

Q: Q.8 P The fixed beam ABhas a hinge MA Cat mid span. A concentrated load Pis applied at C. Whar is…

A: To find the moment MA =

Q: 1-25. Determine the normal force, shear force, and moment in the beam at sections passing through…

A: Given :

Q: Q4: A circular bar ABC, 4 m long, is rigidly fixed at its ends A and C. The portion A 2.2 m long and…

A: I have solved your problem

Q: The beam ABC is to be loaded with a 300 lb/ft uniform distributed live load so it causes the largest…

Q: Determine the internal normal force, shear force, and bending moment in the beam at points C and D.…

Q: 0.5 m -3 m- 0.5 m 175 N/m -3 m- 200 N/m What is w (N/m) & d (meter) of the support on the right to…

Q: Find the moment reaction at the support Mr. Find the force reaction at the support Ry

Q: 6 A 72 C W 2 T 30⁰ D B 12 A beam AB of length 1 and weight w supports a load W at its free end B and…

Q: the cantilever method and determine tely) the reactions at supports A, B, C, and D. have the same…

Q: 7-33. Determine the maximum magnitude Pof the loads the beam can support if the average shear stress…

A: The given figure is shown below:

Q: *5-48. If rope BC will fail when the tension becomes 50 kN, determine the greatest vertical load F…

Q: M. A B E Hinge /C D L2 4 m 6 m

Q: Solve for the maximum shear at the point C of the beam below when subjected to the series of moving…

A: A beam simply supported at A and B to this a train of load passes through. The beam consists of two…

Q: 1. The truck loading shown below represents the design load for an 80-foot, simple span bridge…

A: As per bartleby guidelines experts are allowed to solve only first three parts. If you want other…

Q: 3m long cantilever ABC is built-in at A, partially supported at B, 2m from A, with a force of 10kN…

Q: R12-1. Sketch the intensity of the shear-stress distribution acting over the beam's cross-sectional…

A: The given figure is shown below:

Q: What is the reaction force at point B of this beam? 7P A 7P/2 7P/3 7P/4 B 2L/3L/3 P C

A: Given Data Determine the reaction force at point-B.

Q: Find shear (V) (in kN) and moment (M) (in kN • m)

A: Shear force: - It is a force which acts parallel to cross section of body.

Q: The strut is supported by a pin at C and an A-36 steel guy wire AB. If the wire has a diameter of…

Q: F4-29. Replace the loading system by an equivalent resultant force and couple moment acting at point…

A: To find resultant and moment about point O

Q: Solve the bending moment, 6ft to the right from A. 16k 2 k/ft 8k 3 k/ft ID B. E 12 ft-8 ft- 9 ft- 12…

Q: Determine the internal normal force, shear force, and bending moment in the beam at point D. Assume…

Q: Problem 2: The force F = {400i – 100j – 700k} lb acts at the end of the beam. Determine %3D the…

Q: F4-3. Determine the internal normal force, shear force, and bending moment acting at point C in the…

Q: 2- The compound beam is subjected to a uniform dead load of 200 lb/ft and a uniform live load of 150…

A: A compound beam with a fixed end at A and roller end at C, hinged at B is given. To this beam…

Q: 1.Determine the max force that can be developed in member CD due to the live load of 800lb/ft which…

Q: ed ASAP

Q: D 3rd. G H ZK K. L M P. 1.St. そ20 そとo-30 つ!

A: To solve this problem we will use Portal method. In Portal method point of contraflexure occur at…

Q: 6 6-22. The beam is subjected to a uniform live load of 1.2 kN/m, a dead load of 0.5 kN/m, and a…

A: Given Span 16 mDead load = 0.5 kN/mLive load = 1.2 kN/m and 40 kNTo find out Maximum positive shear…

Q: 4. Section A certain truck passes a girder with a simple span of 17 m. Truckload: 3 kN 8 kN 15 kN 3…

A: Given load distribution on the span of 17 m.

Q: 9000 N/m 6000N 8000 N/m A 4 m 22m 2m 4 m DIE

Q: -2.4 m-t- 6m -2.4m- 1. For the electric transmission tower shown, 1.2 m a. Determine if the truss is…

A: A electric transmission tower is given in the question supported on hinge support at both the ends.…

Q: Problem No 3 A wide flange section has the following properties bf = 150 mm tf = 12 mm Fy 250 MPa =…

A: The breadth of the flange, bf = 150mmThe thickness of the flange, tf = 12 mmThe thickness of the…

Q: Determine the Maximum Bending Moment for the beam shown.

A: ∑MA=0265×3 - 245 + 30×6×9 - RD×9 = 0RD=241.11 kN∑V=0RA+RD=265 + 30×6RA+241.11=265 + 30×6RA=203.89 kN…

Question

40 ft-
B
-60 ft-
-14 ft-30 ft-
4k 16 k
16 k
5. For
For the bridge beam shown,
determine the shear at point B of the
beam due to the wheel loads when the
front axle of the truck is located at a
distance of 16 ft from the left support A.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

1. Determine the equivalent force-couple system at the pin (point O) and roller support. Also, compute the x-intercept of the line of action of the system resultant treated as a single force R of the three forces acting on the simple truss at the pin and roller support. 30° 20 kN 25 kN 5m 3 m 6 m 3 m 30 kN
Subject the beam shown below to a UDL of 1.5 kN/m, a ULL of 4.0 kN/m and the given wheel loading to the right. Joint A is fixed, B is an internal hinge, and C is a roller support. Locate the loads to calculate the maximum shear at B and the maximum moment at A. 5kN 5 m 5m DG 20kN 10 m MAIN PEN
Draw the 25 16. A shear 1-3ft-1- 9ff K moment the 30 lb-ft beam. diagram. C 7) J 4-4₁5ft - D 180 lb-ft
6-65. Determine the horizontal and vertical components of force that pins A and B exert on the frame. C2 kN/md 4 m A -3 m- B
Draw the (a) axial (b) shear and (c) bending moment diagram of the girders. Use portal method for structure (1), cantilever method for structure (2) and Factor Method for structure (3). All columns have the same area. The beams and columns have the same modulus of elasticity. Assume moment inertia of beams is twice the moment of inertia of columns. (1) 15 kN E 6 m B 8 m 8 m (2) 5k 12 ft 4k 12 ft 15 ft (3) H G 3 k 15 ft E F 4k 15 ft B 18 ft -20 ft
draw the shear diagram and moment diagram for the girder. show all work
Determine the resultant forces at pins B and C on member ABC of the four-member frame.
For this indeterminate truss, solve the magnitude of the axial force of members FG, GO, and NO. Indicate whether it is compression, tension, or neutral. E G 3m D H N 3m P (kN) R I 3m в L J 3m A K 3m 3m 3m 3m Draw the shear, moment, elastic curve, and axial diagram. 1SP (16) 0-8P (b/ft) 2ft 2ft 2ft
The compound beam is subjected to a uniform dead load of 2 kN/m and a single live load of 14 kN. Determine (a) the maximum negative moment created by these loads at A, and the (b) maximum positive shear at B. Assume A is a fixed support, B in an internal pin, and C is a roller. TC A |B 國 5m 2m