1. The truck is moving along a 20 m span of beam. The front axle is 30 kN, the middle is 75 kN an the rear is 45 kN. The middle load is space 4m from the front and 8 m from the rear. a. Determine the moment under each axle. b. Calculate the maximum moment produced by the load. c. Calculate the maximum shear. 45 KN 75 KN 30 KN 8 m- A 3 20 m 2 4m 1 B

1. The truck is moving along a 20 m span of beam. The front axle is 30 kN, the middle is 75 kN an the rear is 45 kN. The middle load is space 4m from the front and 8 m from the rear. a. Determine the moment under each axle. b. Calculate the maximum moment produced by the load. c. Calculate the maximum shear. 45 KN 75 KN 30 KN 8 m- A 3 20 m 2 4m 1 B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

method of analysis of statically indeterminate structures by the force method please use FORCE METHOD 9-21. Determine the reactions at the supports. Assume A is fixed and the joint at B is rigid. EI is constant. Prob. 9-21 10 kN/m 30 kN/m B O A 3 m C 3 m
Beam AB has a negligible mass and thickness, and it supports the 200 kg uniform block. It is pinned at A and rests on the top of a post, having a mass of 20 kg and negligible thickness. Determine the two coefficients of static friction at B and C so that when the magnitude of the applied force is increased to P = 300 N, the post slips at both B and C simultaneously. A 1.5 m t-1.5 m- 1 m 0.75 m
Given: Consider the truss shown below and the series of loading. 20 k Required: 8⁹ An 8⁹ 8⁹ 8' 8' a 10 k 8' (A) (A) Calculate the force in member bd for case (A) (B) Calculate the force in member bd for case (B) (C) Calculate the force in member bd using the principle of superposition for the truss loading below. DO NOT use equilibrium equations. 10 k d 5 k a 8⁹ 8' (B) b 8'
3. The shear stress is limited to 60 MPa. Consider G = 84,000 MPa. a. Determine the diameter of a solid steel shaft which will transmit 90kW at 106 revolutions per minute.. b. Determine the length of the shaft if the twist must not exceed one-degree over the entire length. (
For the Beam and loading shown Determine bending moment at A in KN.m IF W= 41, a=1 m w kN w kN/m 2w kN m A . B ra m- a m→-a m a m А. -123.0 В. -205.0 C. -41.0 D. 0.0 Е. -20.5
fy = 345 MPa f'c = 28 MPa Determine the Nominal Moment Capacity in kN-m. Beam as shown: 600 3-28mm 250 K
Problem 1 If roller support is added at point C, 20ft. from point A. Determine the following: (Use Conjugate Beam Method) 2 k/ft A B 30 ft El = constant E = 29,000 ksi | = 3,000 in. Required: 1. Reaction at A 2. Reaction at C 3. Moment at A
The small crane is mounted along the side of a pickup bed and facilitates the handling of heavy loads. When the boom elevation angle is 0 = 37°, the force in the hydraulic cylinder BC is 4.1 kN, and this force applied at point C is in the direction from B to C (the cylinder is in compression). Determine the moment of this 4.1-kN force about the boom pivot point O. The moment is positive if counterclockwise, negative if clockwise. 610 mm 105 mm 285 mm 345 mm B Answer: Mo = kN-m
(6) Determine the reactions at A and B for the beam subjected to the uniform load distribution. Draw the N,V,M diagrams. y I 4 kN/m L--x B 500 mm- A) A 400 mm-
1. A frame held taut by a rope connected at D and E, is pin connected at B. If 1500 N is perpendicular to the member AB, determine the tension on the rope and the horizontal and vertical components of forces at B. Assume roller connection at A. 2000 N 2 m Fim--1 m- 1500 N 2 m 2 m 45° A
The bar is snugly fit between points C and A before the loading is applied at Collar B. Assume E = 200 GPa for the steel. The circular bars in the assembly are solid. The bars are solid with a diameter of 15 mm. Assume a fixed rigid support at C and A. A C В 6 kN 3 m 2 m A) Show the FBD and compatibility equation for this problem. B) Determine the support reactions at A and C. (Horizontal forces only) Left side: Fc = Right side: FA =
The motor A delivers 3000 hp to the shaft at 1500 rev/min, of which 1000 hp is removed by gear B and 2000 hp is removed by gear C. Determine (a) the maximum shear stress in the shaft; and (b) the angle of twist of end D relative to end A. Use G = 12 x 106 psi for steel, and assume that friction at bearing D is negligible. A 4 in. 3.5 in. 3.5 in. ID В C te-4 ft- | 2 ft - 6 ft-