The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading as shown.Determine the maximum moment in kN-m. Given: w- 5 kN/m, W2 = 6 kN/m, a = 2 m, andb- 5 m. Neglectthe mass of the beam.w2 kN/mw1 kN/mAAAAAAAAb mamA.

In question we have given cantilever beam . Here we consider the anticlockwise moment as negative…

The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading as shown. %3D Determine the maximum moment in kN-m. Given: w1 5 kN/m, w2 6 kN/m, a 2 m, and b = 5 m. Neglect %3D the mass of the beam. w2 kN/m w1 kN/m A am bm

The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading as shown. %3D Determine the maximum moment in kN-m. Given: w1 5 kN/m, w2 6 kN/m, a 2 m, and b = 5 m. Neglect %3D the mass of the beam. w2 kN/m w1 kN/m A am bm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

41. FIND a. Vertical reaction at C b. Horizontal reaction at C. c. Axial force at member AB.
A load P is supported by a structure consisting of rigid bar ABC, two identical solid bronze [E = 13700 ksi] rods, and a solid steel [E = 32600 ksi] rod, as shown. The bronze rods (1) each have a diameter of 0.84 in. and they are symmetrically positioned relative to the center rod (2) and the applied load P. Steel rod (2) has a diameter of 0.5 in. Assume L1=37 in and L2=66 in. If all bars are unstressed before the load P is applied, determine the normal stresses in bronze rods (1) and steel rod (2) after a load of P = 27 kips is applied. (2) (1) L2 (1) L1 A P
1. A 200mm x 300mm beam has a simple span of 8 meters. It is necessary to place a support at midspan because of the excessive deflection at the center in order to limit the deflection to 12mm and such that the moment at that point is zero. E = 13,800 MPa. a. Determine the load carried by the beam. Express your answer in N/m. b. Compute for the reaction at the support at midspan so that the beam will not deflect at its midpan. c. Find the bending stress of the beam so that it will not deflect at its midspan. W- N/m 4m Pz 200 mm RI 300mm
Determine the bending moment (M) in kNm at the point x = 4.5 m from point A for the beam as loaded in Figure 3.2b6. Given a = 2, b = 5 and w4 = 6. Wą kN/m C В a m b m
The cantilever beam carries a combination of a uniformly distributed load and a trapezoidal loading as shown. Determine the maximum moment in kN-m. Given: w1 = 5 kN/m, w2 = 6 kN/m, a = 2 m, and b = 4 m. Neglect the mass of the beam. w2 kN/m w1 kN/m B|I am bm A.
Answer this question
Solve B Please fast
The beam AB has a moment of inertia I = 800(106)mm4, and rests on the smooth supports at its ends. A 50 mm in diameter post CD is placed at the center of the beam. If the temperature of the rod is increased by 100 °C, determine the force developed in the rod. The beam and rod are both made of steel for which E = 200 GPa and α = 11.7(10-6) /°C.
Part I. Principle of Superposition. For the beam loaded as shown, it is required to determine the distribution of internal forces and moments on the beam. El is constant. The supports at B and C are rollers and D is pinned. 10 kN 3 kN/m 3 kN/m В A 3m 3m D 3m 4 kN 1. Determine the degree of indeterminacy of this beam. 2. Solve for all the support reactions. 3. Draw the shear and bending moment diagram for the beam.
For the beam structure shown below, both C and E are rollers, support A is pinned. El is constant within the structure. (1) Determine the degree of indeterminacy of the structure. (2) Choose appropriate redundant(s), then apply the Force Method to calculate reaction forces at all supports. (3) Draw shear and moment diagrams of the beam (4) Apply the Conjugate Beam Method to calculate the vertical deflection at point B. -12 ft- 30 k ↓ B H -12 ft- -12 ft- E = 29,000 ksi I = 1,500 in.4 30 k ↓ D -12 ft-
Example:Determine the force Pneeded to lift the load. Also, determine the proper placement x of the hook for equilibrium. Neglect the weight of the beam. 0.9 m 100 mm 100 mm 100 mm P. B 6 KN
a=3.4 b=43 c=24.2