Part CCalculate the normal force between points A and B.Va AEO It vec?N =kNSubmitRequest AnswerPart DCalculate the normal force between points C and D.nν ΑΣφIt vec?kNN =SubmitRequest AnswenWhat is the value of the shear force immediately to the left of point B?vecV =kNSubmitRequest AnswerPart FWhat is the value of the shear force immediately to the right of point B?Πνα ΑΣφvecV =kNSubmitRequest Answer F1F2AL2.0 mL21.0 mA beam is supported by a pin connection at B and a roler support at D. An upwards force F -1.5 kN acts at the let end of the beam (point A). A rightwards force 17.6 ANacts at the right end of the beam (point E). A unitormly distributed load w 18 kN/m pushes down on the beam between points Cand E The separation between A and BisL =1 m, and the separation between Cand Dis La -2 m.Part ADetermine the vertical component of the reaction force at point D. Assume upwards forces are positive.ΑΣΦvecDy =kNSubmitRequest AnswerPart BDetermine the vertical component of the reaction force at point B. Assume upwards forces are positive.AZ Itvec?By =kN%3DSubmitRequest Answer

Given a overhanging beam with loading conditions. It is asked to find vertical reaction at B and D…

F₁ A F₂ 1.0 m 2.0 m L₂ 4₁ A beam is supported by a pin connection at B and a roller support at D. An upwards force F-1.5 kN acts at the left end of the beam (point A) Anghtwards torce F-17.5 kN acts at the right end of the beam (point E) A uniformly distributed load sey -1.8 kN/m pushes down on the beam between points C and E. The separation between A and 8 s L-1, and the separation between C and Dis La-2m W₁ B

F₁ A F₂ 1.0 m 2.0 m L₂ 4₁ A beam is supported by a pin connection at B and a roller support at D. An upwards force F-1.5 kN acts at the left end of the beam (point A) Anghtwards torce F-17.5 kN acts at the right end of the beam (point E) A uniformly distributed load sey -1.8 kN/m pushes down on the beam between points C and E. The separation between A and 8 s L-1, and the separation between C and Dis La-2m W₁ B

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Calculate the force in member BJ. 15 KN 10 KN 10 KN 20 KN A D E 5.0 m 4 @3.0 m 12.0 m
[ series of concentrated axle loads ] Determine the following: a. Maximum negative shear at B b. Maximum positive shear at B c. Maximum positive moment at B d. Maximum reaction at C Use stored values while solving 4 decimal places in final answer
NEED FAST AND COMPLETE SOLUTIONS AND DIAGRAMS.
P kN kN/m 140 kN m A В C D A 1m 1 m Determine the internal moment at a distance of 0.8 m to the right of B. Assume a distance A of 3 m, a point load P of 12 kN, and a distributed load, w= 25 kN/m.
The Beam AB has a length of 10 m. The concentrated load acts at the midspan. Using equations of static equilibrium, determine the Moment at Point A.
B6
A snow load of 3 kPa rests on a roof whose trusses are spaced 3m on center. Find: 1. Determine the magnitude of the equivalent concentrated load acting at point C.2. Determine the force at member BF. Specify if tension or compression.3. Determine the reaction at E
Calculate the member forces of the loaded structure. y 60 kN D 40 kN 7 m В C Cx 3 m -Ax Cy Az tAy 4 m
Problem 5: Replace the loading by an equivalent resultant force and couple moment at point O. 0.5 m 0.7 m F,=(-2 i+5j-3 k) kN 0.8 m F = (8 i– 2 k} kN
If the maximum allowable force (tensile or compressive) in members GF in the pin-connected truss shown is known to be 270 kN. Determine the maximum load P that can be applied to the truss. 6 m 6 m 6m 6m 6m Select one: OA.P= 90.00 KN OB. P = 270.00 KN OC.P = 405.00 KN OD.P = 180.00 KN OE.P = 135.00 KN P.
The beam below is subjected to a uniformly distributed load of 2 kN/m from a A to C, and a uniformly varying load (2kN/m to 5 kN/m) is applied at C to F. Two uniformly distributed loads support the beam on the location shown below. U, 9-2 w, 1 (m) 1 ( 2 (m) 1 (m) D 5. Determine the magnitude of W; in kN/m. 6. Determine the magnitude of W, in kN/m. 7, Determine the maximum moment. B. Determine the location of zero shear.
Determine the displacement at pulley B. The A992 steel shaft has a diameter of 30 mm.