2. For the beam and loading shown, determine the maximum normal stress due to bending. Also draw moment diagram. its shear and 2 kN 140 mm 3 EN/m 160 mm

Q: 1. Determine the maximum moment and maximum shear of the following beams. Draw the Shear and Moment…

A:

Q: 4. A cylindrical container has a diameter of 20 in. and a height of 30 in. If it is to be filled…

A: Specfic gravity=density of fluiddensity of waterVolume of cylinder=πD2h4 converting the dimensions…

Q: ting shown in the figure below, determine: llowable load the foundation could carry using general…

A:

Q: Draw a schematic flow diagram showing processes to treat: (a) Groundwater containing dissolved…

A: (a) Groundwater containing dissolved solids of about 2200 mg/L with hardness around 250mg/L as…

Q: Determine the vertical deflection at point A of the steel beam. Use E = 200 GPa and I = 100x10^6…

A:

Q: Water flows through the curved pipe shown in the figure below where point X denotes the center of…

A: Given: The discharge is 1 m3/s. The diameter of the pipe at the inlet is 0.5 m. The diameter of the…

Q: A 0.375 -in. thick rectangular alloy bar is subjected to a tensile load P by pins at A and B. The…

A: Given data in question  Load 11 kips Thick 0.375 inch Height 3 inch Strain in longitudinal and…

Q: Determine the following: (round off in 2 decimal places.) Moment at point D Maximum Moment Shear…

A: Given Data Determine 1. Moment at point-D.  2. Shear force at 5ft from point-D.  3. Moment at 3ft…

Q: Problem For a given sol, the following are known, G, = 2.70, moist unit weight is 20.3067&N /m², and…

A:

Q: Q- In the layout of an MG track, the versine of a horizontal circular curve is measured over a 17 m…

A: Degree of curve = 2 Chord length = 17 m  To calculate: versine of curve.

Q: III – Moment Area Method 3. Using the moment area method, determine the deflection yc at point C. EI…

A: Using moment area method find deflection at C.

Q: 5.0m 2.0 10.0 m 2.5 8.0 m A cross section through an earth dam is shown in the figure. The earth dam…

A: Given, k=7×10-6 m/sec H=8 m a).Rate of flow through the dam q=KS S=D2+H2-D D=0.3L+x+5+10×2L=8×2.5=20…

Q: Determine the pressure at the top of a 947.1 m tall building under the following conditions:…

A: Answer To calculate the pressure at the top of the building we have Pressure at the bottom of the…

Q: 1. Converging, diverging, transform 2. Pinatubo, Taal, Mayon 3. Sedimentary, igneous, metamorphic 4.…

A: 1.Types of plate boundaries 2.volcano in the Philippines 3.Types of rocks 4.trenches in the…

Q: The beam carries varrying load as shown. Determine the following. Use Double Integration Method in…

A:

Q: For the given beam: (a) Which of the following is the vertical reaction at C. [Select] (b) Which of…

A:

Q: 1. What are the nanomaterials used in your field of study (Civil Engineering)? How are they being…

A: “Since you have asked multiple questions, we will solve the first question for you. If you want any…

Q: Bolted and Riveted Connections 1. From the bolted connection shown, the diameter of bolts is 18mm0…

A: Solution: Given: db = 18 mm dbo = 18+3 = 21 mm Section: 100 x 75 x 8 mm Ag = 1340 mm2 t = 9 mm A36…

Q: An essential 5-story facility structure is conceptualized with an intermediate reinforced concrete…

A:

Q: 2. Use method of members to determine the reactions in the supports and the horizontal and vertical…

A:

Q: 一-キ 山g

A:

Q: 2. Design the dimension of a square footing to carry a column load 1800 kN. The base of the footing…

A: To design the footing, we will proceed by determining the ultimate bearing capacity of the footing.…

Q: Thanks for answering

A: The objective of the question is to calculate the location of the centroid, the second moments and…

Q: F = 25kN 1) The socket wrench AB lies in the plane parallel to xy plane. 10kNm The assembly OAB is…

A:

Q: 7. Water flows under constant head through the two soil samples 1 and 2, as shown in the figure. The…

A:

Q: In 1978, the magnetic bearing of a line OA was N 15°45' W, the magnetic declination at that time is…

A:

Q: A composite beam is under external loads as shown below. a) Draw the internal shear force and…

A:

Q: 1. Based on your field of interest (Civil Engineering), choose a particular equipment or device,…

A: Solution: “Since you have asked multiple questions, we will solve the first question for you. If you…

Q: (3) ) A 6.0 m long simply supported beam is made of HN450×200×8 X 12, Q345steel. The beam carries on…

A: ALSO GIVEN CODE REQUIREMENTS FOR BENDING MEMBERS WITH CONTIOUS LATERAL SUPPORT IS AS BELOW:

Q: 1. A 20-mm diameter commercial steel pipe, 30 m long is used to drain an oil tank. Determine the…

A:

Q: 2. The rated speed of a banked highway curve of 250-meter radius is 60 km/hr. If the coefficient of…

A:

Q: PROBLEM 1 The City of San Fernando is considering building a new parking lot. The land will cost…

A: The given data is as follows: Cost of land=250,000 pesosConstruction cost=1,500.00 pesosAnnual…

Q: 5. A 5-m-high, 5-m-wide rectangular plate blocks the end of a 4-m-deep freshwater channel, as shown…

A:

Q: SITUATION 13: For Items 47-50. 47. Determine the rotation at point B. a. 2.709° (counterclockwise)…

A:

Q: Problem#2: Calculate the force required for a 45-kg box to move in a rough horizontal surface if the…

A:

Q: Determine the magnitude of THE reactions at A and K K 4 ft E A H -3--3--3--3--3- 1500 lb 1500 lb…

A:

Q: Solve for the reactions and draw the shear and moment diagram. (1) (3) (5) (7) 5m 5 m 4m 5 m MN KN-m…

A:

Q: A 60kg attache case cascades down a ramp with uk = 0.2 at an initial speed of 2m/s. How %3D long…

A:

Q: - A circular curve of radius R connects two straights with a deflection angle of 60°. The tangent…

A: Deflection angle- δ = 60o It is needed to find the tangent length T.