Three reservoirs Z, Y, and X meet at junction P. Reservoir Y (25m above Reservoir X) is at Elev. 282m. Pipe Diameter (mm) Length (m) C Pipe Z 750 988 100 Pipe Y 900 1410 110 Pipe X 600 1022 90 If the rate of flow from the highest reservoir, Reservoir Z, is 605 L/s, then: Determine the discharge through the pipe connected to Reservoir X? 0.879 cu.m/s 0.872 cu.m/s None of the choices 0.605 cu.m/s

Three reservoirs Z, Y, and X meet at junction P. Reservoir Y (25m above Reservoir X) is at Elev. 282m. Pipe Diameter (mm) Length (m) C Pipe Z 750 988 100 Pipe Y 900 1410 110 Pipe X 600 1022 90 If the rate of flow from the highest reservoir, Reservoir Z, is 605 L/s, then: Determine the discharge through the pipe connected to Reservoir X? 0.879 cu.m/s 0.872 cu.m/s None of the choices 0.605 cu.m/s

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Three pipes 1,2 and 3 connect three reservoirs A, B and C, respectively, and meet at junction D. The elevation of A is 300 m while that of C is 277m. The rate of flow out of the reservoir B is 560Lit/sec. Pipe Length (m) Diameter (mm) Friction Factor 1 1200 800 0.0175 2 800 450 0.0208 3 1800 500 0.0183 Which of the following nearly gives the rate of flow in pipe 1? a. 45.91 L/s b. 122 L/s c. 459.78 L/s d. 514.09 L/s Which of the following nearly gives the rate of flow in pipe 3? a. 100.22 L/s b. 45.91 L/s c. 459.78 L/s d. 514.09 L/s Which of the following nearly gives the elevation of reservoir B? a. 360.55 m b. 336.67 m c. 323.37 m d. 3.90 m
Determine the flow (m³/s) in each pipe in the figure shown and the elevation of reservoir C if the inflow to reservoir A is 515 L/s.
Determine the flow in each pipe in the reservoir shown below. Use the values provided in the table. Elevation Reservoir A 80m в 50m 20m Pipe Diameter Length friction factor AP 400mm 1800m 0.027 BP 500mm 2000m 0.02 СР 700mm 3500m 0.025 El. A El. El.
Three reservoirs are connected by a piping system and the properties of the pipes are as shown below. If the rate of flow from reservoir A is 1200 LPS, and the friction factor, f for all the pipes is 0.025, determine the following: a. Discharge of reservoir B b. Discharge of reservoir C c. Elevation of reservoir C
subject: hydraulics engineering
Reservoirs A, B, and C are connected by pipelines 1, 2, and 3 respectively which meets at the junction D. Reservoir A is at elevation 80 m, reservoir B is at elevation 50 m, and reservoir C is at elevation 10 m. Diameter Length Friction Factor 400 mm 500 mm Pipe 1800 m 2000 m 1 0.02 2 0.025 3 800 mm 4000 m 0.03 a. Compute the discharge flowing out of reservoir A. b. Determine the discharge flowing in or out at reservoir B. c. Find the discharge flowing towards reservoir C.
do not round off everything
Three reservoirs A, B, and C are connected by pipelines 1, 2, and 3 respectively which merges at a junction X. The elevation of reservoir A is 300 m and that of B is 285 m. The rate of flow from reservoir A is 1.4 m/s. Diameter Length Friction Factor Pipe 1 800 mm 1500 m 0.0157 2 600 mm 450 m 0.0162 3 450 mm 1200 m 0.0177 Find the rate of flow in reservoir B. Calculate the rate of flow in reservoir C. Solve the elevation of reservoir C.
SITUATION 2: Three reservoirs A, B, and C are connected respectively with pipes 1, 2, and 3 joining at a common junction P. Reservoir A is at elevation 80 m, reservoir B at elevation 70 m and reservoir C is at elevation 60 m. The properties of each pipe are as follows: Elev 80 ha hez Elev 70 B 4000 m- 250 mm f-0.018 he 3500 m f- 0.018 Elev 60 Pipe 1: L= 5000 m, D = 300 mm Pipe 2: L= 4000 m, D = 250 mm Pipe 3: L= 3500 m 5000 m - 300 mm f= 0.018
A pipe, diameter 15 cm, leaves a straight pipe with a diameter of 10 cm at point A, and later rejoins it at a downstream point B. The distance AB on the straight 10 cm pipe is 700 m. How long will the 15 cm pipe have to be in order that the flow in the two parallel pipes may be equal? Use f=0.020, and neglect minor losses. 4892 m. 5315 m. 6072 m. 4367 m.
Determine the flow in L/s into or out of each reservoir in the pipe system shown; use n=0.011 for all pipes
01(a) There are two reservoirs, A and B, with the water surface elevation in A 10 m higher than that in B. These are connected through two pipes in series with pipe 1 starting from A and pipe 2 ending in B. Lengths of both the pipes are 100 m, diameter of pipe 1 is 30 cm and diameter of pipe 2 is 25 cm. At the junction of these pipes, water is being withdrawn at the L v² D 2g rate of 0.02 m³/s. Friction loss in the pipes is given by h = f and the Darcy friction, f, entrance and at the junction, for both pipes is 0.02. Neglecting the head losses at the estimate the total water withdrawal from reservoir A.