Three pipes of length 800 m, 500 m, 400 m, and of diameter 500 mm, 400 mm and 300 mm respectively are connected in series. These pipes are to be replaced by a single pipe of length 1700 m. Find the diameter of single pipe.

Three pipes of length 800 m, 500 m, 400 m, and of diameter 500 mm, 400 mm and 300 mm respectively are connected in series. These pipes are to be replaced by a single pipe of length 1700 m. Find the diameter of single pipe.

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Water and oil flow in two pipeline in figure below using the double U-tube manometer as connected ,find the pressure difference PA-PB (PSI)? - Air G 1.5 ft Water 0.5 ft SAE 30 B 2 ft 2,5 ft - Mercury
A water tank with a depth of h open to the atmosphere will be discharged through an outlet pipe with a diameter of 1 cm. The density of water is 1000 kg/m3, dynamic viscosity is 0.001 kg/ms. The pipe is 20 m long and there is a pump and a full open angle valve on the pipe. If the pump head supplied by the pump is hp = 2 m, the pressure at the outlet is 150 kPa and the outlet flow rate = 0.001 m3/h, calculate the height h. (Take atmospheric pressure as 100 kPa).
A pipe has an outer diameter of 26 mm and an inner diameter of 19 mm. What is the polar moment of inertia "J" for the shaft in mm^4? Type your answer...
A pipe connected in series has the following roughness or friction coefficients: Pipe 1 C = 80 (Hazen-Williams) Pipe 2 n = 0.015 (Chezy-Manning) Pipe 3 f = 0.025 (Darcy-Weisbach) All pipes have a diameter of 400mm, length of 1 kilometer, and flow rate of 150 L/s. Determine the headloss on Pipe 1 in meters.
A PIPELINE WITH A PUMP LEADS TO A NOZZLE AS SHOWN. FIND THE FLON RATE WHEN PUMP DEVELOPS AN 80FEET HEAD. ASSUME HEAD LOST IN THE 8-INCH PIPE TO BE THERE TIMES ITS VELOCITY HEAD WHILE THE HEAD LOST IN THE 4-INCH PIPE TO BE TEN TIMES VELOCITY HEAD. FIND: a)COMPUTE THE FLOW RATE b) FIND THE PRESSURE HEAD AT THE SUCTION SIDE. PLEASE ANSWER IMMEDIATELY WITH COMPLETE SOLUTION THANK YOU!
Water is pumped from a supply reservoir to a ductile- iron water-transmission line, as shown in Figure 2.26. The high point of the transmission line is at point A, 1 km downstream of the supply reservoir, and the low point of the transmission line is at point B, 1 km downstream of A. If the flow rate through the pipeline is 1 m3/s, the diameter of the pipe is 750 mm, and the pressure at A is to be 350 kPa, then: (a) estimate the head that must be added by the pump; (b) estimate the power supplied by the pump; and (c) calculate the water pressure at B. Supply reservoir Elev. 7 m Pump Elev. 10 m Transmission line Elev. 4 m- B Figure 2.26: Water pumped into a transmission line
A cylinder having a diameter of 6 in (152mm) and a stroke length of 25 in (635mm). The exit time will be 5 seconds. The system operates with a pressure of 50 psig (3.45 bar) and there will be a pressure loss of 2 psi. What will be the Cv of the valve to be installed? [Answer: 1.99]
A municipality wants to determine the flow rate into the plant based on pipe size, elevation difference, and assumed roughness, for the water supply reservoir is shown in the figure below. The pipe is an old 4-inch diameter Cast Iron with a Hazen Roughness coefficient of 100 & 223 feet long. The difference in elevation is 62 feet. The pipe has a strainer at the entrance (k-1.9), a valve (k=8.6), a check valve (k = 2:7) and 3- 90° bends (k-0.83). The flow exits into a receiving pond at the WTP. Provide the flow rate in Gallons Minute. per WTP Az
2. The total flow from A to E is 300 L/s. Compute the flow for pipes 2, 3, 4, and 5 3 5 D 6 Pipe 1 2 3 4 5 6 f 0.02 0.02 0.02 0.02 0.02 0.02 Diameter Length (mm) in (m) 450 400 250 360 200 600 300 1400 250 450 300 700
1. [Ch4 – 2] A hydraulic oil with the absolute viscosity of 0.09 N.s/m² and specific gravity of 0.9, is flowing in a 30-mm- diameter pipe at a velocity of 6 m/'s, detemine: a. The Reynolds number? Is the flow laminar or turbulent? b. The head loss due to friction in units of bars for a 100-m length of smooth pipe. 2. [Ch4 - 2] The kinematic viscosity of a hydraulic oil is 0.0001 m/s. If it is flowing in a 20-mm- diameter commercial steel pipe, find the friction factor for: a. The velocity of 5 m/s b. The velocity of 50 m/s
2.2 m/min The figure represents a simplified pipe 305 mm Infiow 1000 m 25 m /min network. Flows for the area have been disaggregated to the nodes, and a major fire flow has been added at node G. 25+ m/min The water enters the system at node A. 250 mm a.5 m/min 1100 m 8 200 mm 500 m Pipe diameters and lengths are shown on the 2.0 figure. 200 mm E 500 m 1.5 m /min Find the flow rate of water in each pipe using the Hazen-Williams equation with Crw F = 100. Carry out calculations until the 305 mm 1100 m G corrections are less then 0.2 m/min. 2.3m/min 14 m/min 305 mm 305 mm 1250 m w 0001 405 mm 1250 m 355 mm 355 w 009 w 00 ww 002 C w 00