The properties of three pipes connected in series are tabulated below. (a) What is the head loss (ft) in each pipe for a total head loss in the system equal to 30 ft? (b) What is the flow rate (cfs)? pipe L (ft) d (in) f 1 1200 8 0.015 2 1000 6 0.015 3 2000 10 0.015

The properties of three pipes connected in series are tabulated below. (a) What is the head loss (ft) in each pipe for a total head loss in the system equal to 30 ft? (b) What is the flow rate (cfs)? pipe L (ft) d (in) f 1 1200 8 0.015 2 1000 6 0.015 3 2000 10 0.015

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: With velocity of 7 m/s in the 330 mm diameter pipe in the figure shown, determine the discharge in…

Q: Two pipes 1 and 2 of the same length and diameter are connected in parallel. If f2 = 0.914f1, the…

A: solution Given we know hf=flv2d×2g=flQ212.1d5given f2=0.914f1as the pipes are parallel the head loss…

Q: wo pipes 1 and 2 of the same length and diameter are connected in parallel. If f2 = 0.9f1, the flow…

A: solution Given friction in pipe 1 =f1friction in pipe 2=f2and f2=0.9f1as the pipes are parallel head…

Q: Calculate the discharge in pipe 3, in m^3/s.

A: Step: 1 Head loss: - In fluid system, energy dissipated due to friction along the hydraulic system…

Q: Determine the forces in members EH and EI of the double Fink truss (positive if in tension, negative…

A: Solution Find the support reactions VA +VG = 7L But, VA =VG , according to the symmetry So, VA =…

Q: Example For the branching system shown in Fig. 11.14, calculate the discharge each pipe. Take f =…

A: Determine the discharge in each pipe.

Q: 1. The represents the roughness of a pipe whereas the Icoefficient accounts for the roughness of the…

A: This question is related to the Fluid Mechanics from Civil Engineering. This question is based on…

Q: 45KN /m (10KN-m 11OKN. m 135KN 270KN 135KN Gm Gm.

Q: SITUATION. The total head lost from A to E in the pipe system shown in the figure above is 15m.…

Q: Q3(a). Find the missing flow rate (Q2) in the pipe system shown below? Assume steady state and ideal…

A: Given diagram:- The given value of total flowrate is, Q=10 m3/s The given value of Q3 is, Q3=7 m3/s…

Q: For the pipe network shown in the figure below, what is the flow rate in pipe BA? C O 350 GPM 422…

Q: Questions #1 Water flows at the rate of 0.16 L/s through a 200 mm diameter pipe. If its Viscosity…

Q: 2) In the figure shown pipes are in parallel connection with properties given. If the flow into the…

Q: Question 1: Mr. Yaseen is the Chief Engineer at one company. He assigned his staff engineers to…

A: ### Velocity in different pipes of a piping system of three connected tanks### By using Bernoulli…

Q: The flow from A to E is 0.280 cum/sec. Using n = 0.09 Pipe 1 (Diameter and Length): 450 mm, 300 m…

A: The flow from A to E is 0.280 cum/sec. Using n = 0.09 Pipe 1 (Diameter and Length): 450 mm, 300 m…

Q: The duct shown in the figure has a reduction of 1 to 2, discharge to the atmosphere in section 3,…

A: Flow rate is defined as the rate at which fluid is flowing in a given tube or section having…

Q: 2. A pipe carries water at a flow rate of 90 L/s. Determine the minimum inside diameter so that the…

A: Given :- Flow rate of the water (Q) = 90 L/s Also, 1000 L/s = 1 m3/s So, Flow rate of the water (Q)…

Q: A liquid flows through a venturi meter whose inlet diameter is 31 inches and throat diameter is 19…

Q: Three pipes of different lengths and diameters connected in series discharge 160 liters/s. If the f…

Q: A pipe network is show in figure below; find the distribution of discharges in all pipes and…

Q: 1. Find the flow rates in each pipe, neglecting minor losses. 110m 50 m 25 m L (m) D (m) € (m)…

Q: Three cylinders weigh 181 N each and 86 mm diameter are placed in a channel of 198 mm width.…

A: Given:- The magnitude of the weight of three cylinders = 181 N The diameter of each cylinder = 86 mm…

Q: The figure shows a pipe network with initial discharge that is used to find the discharge in each…

A: The fluid mechanics is the subject of designing which will be helpful in many designing discipline.…

Q: Equivalent pipe method QUIZ: Find the equivalent pipe for the pipes system shown in figure below A…

Q: For the pipe network shown, the flow of water from A to the first junction is 2 cubic feet per…

Q: An clectrostatic precipitator is being designed to operate at an efficiency of 97%. Using the…

Q: Three pipes are connected in parallel, The difference in heads in each pipe is 40 m. Pipes Diameter…

Q: Pipe 1: Length = 1000 m; Ø 900 mm; n = 0.011 B Pipe 2: Length = 650 m; Ø 450 mm; n = 0.011 Pipe 3:…

Q: pipeline between point A and B consists of 1000 ft of 18in followed by 800 ft of 12in…

Q: Q1, ( through a filter and then is circulated back to the tanks as shown below. The flowrate is 0.08…

A: Given, Q = 0.08 cfs v = 1.21 x 10-5 ft2/s

Q: It is desired to pump 390 liters per second of water from a stream to a pool as shown in the figure…

A: Q = 390L/s = 0.39m3/s

Q: Find the discharge through each pipe in the network of pipe shown below: (Taken n = 2) 20 r=5 >50…

Q: Quèstion 49 Avertical cylinder having a circular base of radius 'r and a height of 12 m is filled…

Q: A discharge of 600 liters/sec flows through a pipe having a diameter of 400 mm., length of 40 m.…

Q: For the system shown in the figure below, obtain the pipe discharge values as well as the node…

A: Let the friction factor for all pipes is fhead loss due to friction between node 2 to 6 is…

Q: 1. A horizontal pipeline reduces from 190 mm diameter to 70 mm diameter. Water enters the pipe at…

Q: Pipe No. Length - m Diameter - cm 1 1000 90 2 500 50 600 40 4 800 700 75

Q: For the pipe network given in the figure, the pipe flow rates in the intermediate lines, the given…

Q: The figure illustrates a piping system with three tanks. Determine the flow rate of each pipe…

Q: Calculate the pipe diameter required to provide 0.0057 m³/s of a fluid with = 6.09E-6 m²/s at T-15…

Q: Your company will build a water tank to service a building that is 100 ft away with 20 psi water…

A: Pressure required= 20 psi Head required for this pressure = 46.133 ft Distance of service building =…

Q: The figure illustrates a piping system with three tanks. Determine the flow rate of each pipe using…

Concept explainers

Storm Sewers and Detention

The storm drains system transports rainwater or stormwater and other runoff from roads, parking lots, and roof downpipes directly to nearby creeks, rivers, or the sea without any treatment.

Question

The properties of three pipes connected in series are tabulated below.
(a) What is the head loss (ft) in each pipe for a total head loss in the system equal to 30 ft?
(b) What is the flow rate (cfs)?
pipe L (ft) d (in)
f
1
1200
8
0.015
2
1000
6
0.015
3
2000
10
0.015

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step by step

Solved in 2 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

... L = 700m 2 4 D = 45cm L = 800m D = 40cm L = 600m L = 700m D = 35cm D = 35cm 1 A L = 700m В D = 40cm L = 1200m D = 40cm Water is flowing from point A to point B in the system shown in the figure. All the corresponding length and diameter of each pipe is shown. Assuming that each pipe has n=0.011 and head loss from point A to B is 30m, determine the a) discharge at pipe 1 b) discharge at pipe 3 c) discharge at pipe 5 A Q3 = 0.160 cu.m/s B) Q1 = 0.253 cu.m/s 3.
I need the answer as soon as possible
11.20 3. Parallel Pipe Three pipes are in parallel with a total head loss of 20.3 m. The pipe data are pipe 1 2 3 L, m 100 150 80 d, cm 8 6 4 €, mm 0.24 0.12 0.20 €/d 0.003 0.002 0.005 The fluid is water, p = 1000 kg/m³, and v= 1.02 x 10-6 m²/s. Calculate the total flow rate in cubic meters per hour, neglecting minor losses.
14
4- Consider the system shown in the figure. If a change of P kPa in the pressure of air causes the brine- mercury interface in the right column to drop by d mm in the brine level in the right column while the pressure in the brine pipe remains constant, determine the ratio of A₂/A₁. P (kPa) d (mm) 6 Sum of last 2 digits of 35 YorkU ID# ending with 0, 2, 4, 6, 8 Sum of last 2 digits of 45 YorkU ID# ending with 1, 3,5,7,9 7 Area, A₁. Air Water Mercury SG = 13.56 Brine pipe SG = 1.1 Area, A₂
Q2/ If the flow rate of water through the pipe system shown in Figure shown 2 below is 0.05 (m/s) under total head loss of 0.9 (m) determine the diameter of pipe C. Assume f = 0.02 for all pipes and neglect the minor losses Pipe A 300 m, 200-mm diameter Pipe B 266 m, 160-mm diameter Pipe C 190 m Pipe D 510 m, 250-mm diameter
HYDRAULICS
subject: hydraulics engineering
2. A large-capacity faucet is to be connected to a water main by 20-mm diameter copper tubing as shown in Figure below. The copper tubing has an estimated f=0.02, and local head losses are created by the corporation stop (C-stop), three bends, and the faucet itself. The faucet exit has a diameter of 12 mm. What is minimum pressure in the water main required to obtain a desired flow rate of 50 L/min when the faucet is fully open? fig1.Faucet connected to water main. Water main Bend 3.5 m C-stop E 2 5m Pipe Bend Bend E Bend 4 m Faucet Fitting C-stop Bend(s) Faucet K 9 1.2 10
Given below are pipe lengths, sizes, and connections. All pipes have a friction factor of 0.020. If the flow from A to B is 8 cfs, Determine the head loss in feet in PIPE 5. *23.8062*9.0254*1.0666*2.6570 Determine the flow in the upper branch pipe Q2 in cubic feet per second. *2.6667*2.3809*4.8840*12.4747 Determine the head loss in feet in PIPE 2. *3.4373*8.0165*9.2849*10.4720 Determine the total head loss in feet between the inlet A and the outlet D. *9.2849*13.1625*17.3474*35.9163
I need the answer as soon as possible
Q4/ Compute the flow rate of water through the 3 pipes connected in series as shown In the Figure below. Let f= 0.016 and neglect minor losses. Pipe No. Diameter of Pipe d (mm) 300 200 250 1 2 3 Water 20 ft Lenth of Pipe L (m) 33 50 40 150 ft. 8-in diameter 120 ft, 10-in diameter 100 ft, 12-in diameter Water Fig. 10-2