Q4/ Compute the flow rate of water through the 3 pipes connected in series as shownIn the Figure below. Let f= 0.016 and neglect minor losses.Pipe No.Diameter of Piped(mm)300200250123Water20 ftLenth of PipeL(m)335040150 ft. 8-in diameter120 ft, 10-in diameter100 ft, 12-in diameterWaterFig. 10-2

Answered: Image /qna-images/answer/cc58b408-1772-479e-b4b1-15bdd918291c.jpg

Q4/ Compute the flow rate of water through the 3 pipes connected in series as shown In the Figure below. Let f= 0.016 and neglect minor losses. Pipe No. 1 2 23 3 Water 20 ft Lenth of Pipe Diameter of Pipe L (m) 33 50 40 150 ft, 8-in diameter 120 ft, 10-in diameter d (mm) 300 200 250 100 ft, 12-in diameter Water Fig. 10-2

Q4/ Compute the flow rate of water through the 3 pipes connected in series as shown In the Figure below. Let f= 0.016 and neglect minor losses. Pipe No. 1 2 23 3 Water 20 ft Lenth of Pipe Diameter of Pipe L (m) 33 50 40 150 ft, 8-in diameter 120 ft, 10-in diameter d (mm) 300 200 250 100 ft, 12-in diameter Water Fig. 10-2

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Q2. Determine the flow rates in the three Cast Iron pipes in the figure shown (Assume complete turbulence, rough pipes). P1 Tank 1 Pipe 1 45 m P3 P2 Tank 3 Tank 2 Pipe 3 Pipe 2 D e ipe L (m) e/D f k Pipe Equation (cm) (тm) (m³/s) 1 15 180 20 100 3 12 55 Pressure (P) (pascal) Tank z (m) Total Head (m) 1 50,000 2 300,000 3 70,000
Example 7 (Page 266): Water (T = 20°C) flows from a tank through a 50-cm-diameter steel pipe. Determine the discharge of water. (Include only the head loss in the pipe) Assume the flow is fully developed. Kinematic viscosity: v= 1 x 10-6 m²/s Steel pipe: absolute roughness, & = = 0.046 mm. Water Elevation = 60 m D = 50 cm 100 m Steel pipe 40 m El
4) For the system given in the figure, find the elevation of Reservoir D and the flow direction in pipe 6. Neglect minor losses. El 80 m V A Pipe 1 2 3 4 ||| 5 6 L (m) 600 600 600 700 300 300 P D(mm) 600 600 450 450 450 600 El 90 m B 2 f 0.025 0.025 0.03 0.03 0.03 0.03 3 El 60 m V с 5 6 E1 = ? D
Determine the diameter of steel pipe needed to deliver water (20°C) at a rate of 2 cu. m/s from a reservoir with water surface elevation of 60 m to a reservoir 200 m away with a water surface elevation of 30 m. Assume a squared edge inlet and outlet (k = 1) and no bends in the pipe. Further assume there are two open gate valves in the pipe (k=0.2).
Example 2: A flow of water from a closed reservoir with interior pressure of 50 kPa to a pipe of different diameters shown in figure below. Calculate 1) the discharge and velocity at each pipe, 2) the pressure in each pipe and 3) the .energy and hydraulic grade lines 50 kPa water 10 m D1-300mm D2-200mm D3=100mm D4-50mm (nozzel) 2m
The suction side of a pipe system is as shown in the figure. The pump discharges 495 gpm of water under a total head of 100 ft at 40°F. Atmospheric pressure = 32.7 ft of water. If the required NPSH is 9 ft, will there be a cavitation problem? Please note that 1 cfs equals 449 gpm. 12 ft 6 ft Diameter L = 300 ft Steel = 10 in 5
Determine the flow distribution of water in the system shown in Figure below. Assume constant friction factors, with f= 0.03. The head-discharge for the pump is Hp = 70 m el 50 m Pipe L (m) D (mm) ΣΚ el 48 m 1 100 750 850 350 200 200 [2] [4] 3 el 0m [5] 4 500 200 350 250 [1] [3]
Question 1: The PVC pipeline (ε = 0.0015) depicted in figure below is 150 m. Determine the diameter of the pipe that can provide a flow rate is 0.8 m³/s if the height h is 12 m. Ignore minor losses. water temperature is 4°C. U= h 497 x 10-6 (T + 42.5)1.5 2 m
The circular water pipes shown in the sketch are following full. The velocity of flow (in m/s) in the branch pipe "R" is V = 6 m/s dia = 4 m – મ N=? R V = 5 m/s dia= 2 m
The total discharge (flowrate) from A to B in the figure below is 300 liters/s. Pipe lennthe are: L1= 150 m, and L2 = 450 m. Diameters, are: D1 = 500 mm, and D2 = 250 mm. L1:D1 Q1 Q Q2 L2; D2 Determine [Using Darcy's equation] the headloss [m] and the flowrates (/s] across A-B in pipes 1 and 2 if riyated steel iron pipes are used in the system and flow is FULLY TURBULENT. Flowrate pipe #1 [I/s] =- Flowrate pipe #2 [l/s] =- Headloss pipe #1 [m] =. %3D Headloss pipe #2 [m]
2. The total flow from A to E is 300 L/s. Compute the flow for pipes 2, 3, 4, and 5 3 5 D 6 Pipe 1 2 3 4 5 6 f 0.02 0.02 0.02 0.02 0.02 0.02 Diameter Length (mm) in (m) 450 400 250 360 200 600 300 1400 250 450 300 700
Q4: The pump shown in figure (2) adds 25 kW to the water and causes a flow rate of 0.04 m³/s. Determine the flow rate expected if the pump is removed from the system. Assume f= 0.016 for both case and neglect minor losses. 40-mm-diameter nozzle (2) 60-mm-diameter, 30-m-long pipe; f = 0.016 Pump T h (1) Fig. (2)