04: The pump shown in figure (2) adds 25 kW to the water and causes a flow rate of 0.04 m³/s. Determine the flow rate expected if the pump is removed from the system. Assume f=0.016 for both case and neglect minor losses. 40-mm-diameter nozzle (2) 60-mm-diameter, 30-m-long pipe; f = 0.016 Pump Fig. (2)

04: The pump shown in figure (2) adds 25 kW to the water and causes a flow rate of 0.04 m³/s. Determine the flow rate expected if the pump is removed from the system. Assume f=0.016 for both case and neglect minor losses. 40-mm-diameter nozzle (2) 60-mm-diameter, 30-m-long pipe; f = 0.016 Pump Fig. (2)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Choose only one answer. The best possible answer.
Q2. Determine the flow rates in the three Cast Iron pipes in the figure shown (Assume complete turbulence, rough pipes). P1 Tank 1 Pipe 1 45 m P3 P2 Tank 3 Tank 2 Pipe 3 Pipe 2 D e ipe L (m) e/D f k Pipe Equation (cm) (тm) (m³/s) 1 15 180 20 100 3 12 55 Pressure (P) (pascal) Tank z (m) Total Head (m) 1 50,000 2 300,000 3 70,000
A centrifugal pump with an overall efficiency of 0.56 rotates at 1650 rpm. The flow is purely radial at the inlet of the rotor. The pump has the following characteristics: Flow rate Q = 72 L/s Inlet diameter D1 = 90 mm Outlet diameter D2 = 280 mm Head H = 25m Width at the inlet b1 =20 mm Width at the outlet b2 = 18 mm Leakage q = 2 L/s Mechanical loss Pm = 1.41 kW Blade angle at the outlet β2 = 35 ͦ The water density =998 kg/m^3,Atmospheric pressure 101 kPa a) Determine the hydraulic, mechanical and volumetric efficiencies. b)Determine the minimum number of blades required for the slip to not exceed 0.9. c)Determine the static pressure difference (P2-P1) through the impeller by using Bernoulli equation. d) Determine the available NPSH if the pump is placed 2m above the free surface of the tank and the vapor pressure is ?=2.43 ???.
Three pipes of different lengths and diameters connected in series as shown discharges 169 lit/sec. If f=0.012 and disregarding minor losses, determine a. the head loss in each pipe. b. the diameter of an equivalent single pipe that could replace all the 3 pipes. ASAP
Read the question carefully and give me right solution according to the question
Exercise#3: The figure shows a system. The system is conservative energy between the two valves CV, and CV2. The differential pressure element at point 1 shows a reading for flow rate. This flow rate is equivalent to AP = 3 mmH20 with k factor of orifice equals 20 m² (used as dimension geometry for the pipe). Another turbine flow meter at point 4 shows a reading for flow rate equals 2.7. Based on the reading of the first flow meter, is the turbine flow meter give the correct reading or not? You can utilize the following given information: diameters at point1&2 are D, = D2 = 0.2 m, Dz = D4 = 2 D2, Q1= 3Q2, P4 = P3 – 200000 Pa ,p = 750 Total heads(or energy)of Bernoulli equation at point 1=Total heads(or energy)of Bernoulli equation at point 2+4m, and point2 point1 Total heads(or energy) of Bernoulli equation at point 3=Total heads(or energy) of Bernoulli equation at point 4+10m. CV, 8 Closed DP · Flow meter h tank Turbine Flowmeter CV2 voint4 point3
Plz write neat
Please answer, hydraulics. Thanks
Please answer this... Thank you
Time: 60 Q1: pump puts 2kw in to the system. Find: b. The pressure in the pipe on section side of the pump (at C). a. Discharge. C 5 kPa L = 200 m 10m ↓ Air Water 55 marks 15 m P L = 50m D = 6 cm f = 0.025 D = 8 cm f = 0.030
For the setup shown in the figure :
Three pipes 1, 2, 3 are connected in parallel. The properties of each pipe are given in the table. The combined discharge of the three pipes is 0.61 m3/s. Use Hazen-Williams coefficient of 100 for all pipes. Use table below for the properties of the pipes. a.) calculate the total head loss (A. 181 m B. 461 m. C . 411 m. D. 731 m) b) Solve for the rate of flow in pipe 1 ( A. 0.1249 m3/s. B. 0.1645 m3/s. C. 0.1145 m3/s. D. 0.1225 m3/s). C.) c) Calculate the rate of flow in pipe 2. ( A. 0.1032 m3 /s. ,B. 0.1255 m3 /s. C. 0.7865 m3/s. D. 0.3955 m3/s)