Thoroughly mix the aggregate sample and reduce it to an amount suitable for testing, using asample splitter or by quartering. The minimum sample size should be as follows:Minimum Mass, kgFine aggregate with at least 95% passing 2.36-mm sieve0.1Fine aggregate with at least 85% passing 4.75-mm sieve0.5Coarse aggregate with a nominal maximum size of 9.5 mm1Coarse aggregate of a nominal maximum size of 12.5 mm2Coarse aggregate of a nominal maximum size of 19.0 mmCoarse aggregate of a nominal maximum size of 25.0 mm10Coarse aggregate of a nominal maximum size of 37.5 mm15

Sample Splitters: Sample splitters work by reducing the sample size by leading the flow of the…

Answered: Thoroughly mix the aggregate sample and…

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

The following table provides data obtained during a specific gravity and absorption test on coarse aggregate. Using the data, determine the a) apparent bulk specific gravity, b) bulk SSD specific gravity, and c) absorption of the coarse aggregate.
Coarse aggregate is placed in a rigid bucket and compacted with a tamping rod to determineits unit weight. The following data are obtained:• Volume of bucket = 0.5 ft3• Weight of empty bucket = 20.3 lb• Weight of bucket filled with dry compacted coarse aggregate = 76.8 lba) Calculate the dry-compacted unit weight of the aggregate.b) If the bulk dry specific gravity of the aggregate is 2.620, calculate the percent voids.
Coarse aggregate is placed in a rigid bucket and rodded with a tamping rod to determine its unit weight. The following data are obtained: Volume of bucket =14L Weight of empty bucket = 9.21kg Weight of bucket filled with dry rodded coarse aggregate: Trial 1 =34,75 kg Trial 2 =34.06 kg Trial 3 =35.74 kg a. Calculate the average dry-rodded unit weight b.If the bulk dry specific gravity of the aggregate is 2.620, calculate the percent voids between aggregate particles for each trial.
There are two sources of aggregates (A, B). A sample has been taken from both sources and measured their mass as shown in table below. Measurement Wet mass (9) Oven-dry mass (g) Aggregate A 500 480 Aggregate B 600 564 (a) Determine the total moisture content for the samples from both aggregate sources, respectively. (b) Determine the total moisture content for an aggregate blend with 30% of aggregate A and 70% of aggregate B.
You are given a result of the gradation test of aggregate, calculate and plot the gradation curve on the given semilog graph shee
Design a Mix for the following Data. Specified strength = (99.5) MPa, Required Slump = 80 mmMaximum size of aggregate = 25 mm, FM of fine aggregate = 2.40Grading of aggregate as satisfied by ASTM C33 (American Society for Testing and Materials)SSD specific gravity of fine and coarse aggregate = 2.75Rodded bulk density of coarse aggregate = 1600 kg/cubic mAbsorption Capacity of coarse aggregate = 0.9 %Absorption Capacity of fine aggregate = 0.5 %Moisture Content of fine and coarse aggregate = 2 %Exposure Conditions = Normal
Any solutions please?
Fine aggregate sample was tested to find its physical properties. The test results were as follows: Bulk specific gravity= 2.45, Apparent specific gravity= 2.5, mass of the vessel full of water = 1300 gm, mass of the vessel plus sand and topped up with water= 1500 gm, mass in wet condition 518 gm. Calculate 1- absorption% 2- moisture content% 3- Bulk density 4- Apparent density
To determine the particle size distribution of fine and coarse aggregate by dry sieving.
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve. b. Plot the percent finer in a semi-log gradation chart. c. What is the maximum aggregate size of the sample? d. What is the nominal maximum aggregate size of the sample? e. What is the fineness modulus? Is it in typical range? " Sieve Size, 9.5 4.75 3.35 2.36 2.00 1.18 0.85 0.60 0.425 0.30 0.25 0.18 0.15 (No. 0.075 Pan mm (in) (3/8) (No. 4) (No. 6) (No. 8) (No. 10) (No. 16) (No. 20) (No. 30) (No. 40) (No. 50) (No. 60) (No. 80) 100) (No. 200)| Amount 25 59 75 86 115 136 169 192 225 198 173 112 90 33 12 Datained.
Sieve analysis test for fine aggregates was performed on a sample of fine aggregates and produced the following results: a. Calculate the percent passing through each sieve.b. Plot the percent finer in a semi-log gradation chart.c. What is the maximum aggregate size of the sample?d. What is the nominal maximum aggregate size of the sample?e. What is the fineness modulus? Is it in typical range?

Recommended textbooks for you

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Structural Analysis

Civil Engineering

ISBN:

9781337630931

Author:

KASSIMALI, Aslam.

Publisher:

Cengage,

Structural Analysis (10th Edition)

Civil Engineering

ISBN:

9780134610672

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Principles of Foundation Engineering (MindTap Cou…

Civil Engineering

ISBN:

9781337705028

Author:

Braja M. Das, Nagaratnam Sivakugan

Publisher:

Cengage Learning

Fundamentals of Structural Analysis

Civil Engineering

ISBN:

9780073398006

Author:

Kenneth M. Leet Emeritus, Chia-Ming Uang, Joel Lanning

Publisher:

McGraw-Hill Education

Sustainable Energy

Civil Engineering

ISBN:

9781337551663

Author:

DUNLAP, Richard A.

Publisher:

Cengage,

Traffic and Highway Engineering

Civil Engineering

ISBN:

9781305156241

Author:

Garber, Nicholas J.

Publisher:

Cengage Learning

SEE MORE TEXTBOOKS