ROCK STONEThis question is about material selection process for a solid cylindrical tension rod of diameter d and fixed length L. The rod is to be used in aerospace applications, where light weight, high strength, and high stiffness are all important design considerations. It is tobe subjected to a static axial force, E A safety factor of n, is desired. The materials can be more than one but you need to put your explanation and analysis for justification.a. Derive material Index equation for strength and stiffness.b. Select material for the shaft using the following criterion:1. Light weighti. Stiff materialii. Strong materialiv. Ductile material10001. MODULUS-DENSITYDIAMONDSic SN,ENGINEERINGYOUNGS MODULUS E(G- SE/S: KEWC-CoENGINDERINGCERAMICS-ALUMINASSIALONS 0, O Me ALLOYSW-ALLOYSSTEELS NALLOYSaOa ALLOYS100INPLYiTERYKIRPGEMECFRPAIALLOYS Zn ALLOYSGFRP-GLASSESROCK, STONE OALLOYSCEMENT, CONCRETETINENGINEERING LAMINATESGFRPKFRICOMPOSITESLEADPOROUSASHOAKFIR PINEPARALLELloALLÖYS CERAMICSENGINEERINGMELXALLOYSRALGRAINBALSAWOODPRODUCTSEPOXIESAPMMAPVCNOLANENGINEERINGWOODSNYLONASHOAKPOLYMERSLo---POLYESTERS

Answers The required material properties are : 1. Light weight : Density is ratio of mass to volume.…

This question is about material selection process for a solid eylindrical tension rod of diameter d and fixed length L. The rod is to be used in aerospace applications, where light weight, high strength, and high stiffness are all impo be subjected to a static axial force, F A safety factor of ng is desired. The materials can be more than one but you need to put your explanation and analysis for justification.

This question is about material selection process for a solid eylindrical tension rod of diameter d and fixed length L. The rod is to be used in aerospace applications, where light weight, high strength, and high stiffness are all impo be subjected to a static axial force, F A safety factor of ng is desired. The materials can be more than one but you need to put your explanation and analysis for justification.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

3. Consider a test specimen with the shape of cylindrical rod, 120 mm long to be deformed by tensile load of 28000 N without experiencing plastic deformation or diameter reduction more than 8.5x10-3 mm. Which among the aluminium alloy, brass alloy, steel alloy and titanium alloy are possible candidates with yield strengths 200 MPa, 300 MPa, 400 MPa and 650 MPa, respectively.
Thermo plastic polymers fatigue tested at frequencies above 1Hz display; Excellent resistance to fatigue failure A defined fatigue limit An endurance behaviour with no defined fatigue limit Internal heating during test and a defined fatigue limit
A steel bar which is 457 mm long is repeatedly loaded with 4500 kg in successive tension and compression cycles . Calculate the minimum diameter of the bar which will never fail by fatigue. Given yield point=300 MPa, UTS= 400 MPa , fatigue limit = 306 MPaand Elastic Modulus = 210 GPa
Draw two schematic graphs using pencil showing a typical stress-strain curve for aluminum. The first graph should show engineering stress vs engineering strain, and the second graph should show true stress vs true strain. Label the showing: (i) elastic modulus (ii) proportional limit (iii) yield stress (iv)yield strain (v) fracture stress (vi) fracture strain on each graph. You may showboth graphs on one plot. Explain the difference between engineering stress and true stress.
Consider two cylindrical rods of metal are reduced by a drawing operation: one from Do= 45mm to 15mm and the other from Do=80mm to 30mm. a) what is the longitudinal true strian assuming volume constancy b) which strip will recrystallize at a lower temperature and why
A cylindrical specimen having a cross-section of radius, r, is subjected to a uniaxial tensile force, F, as shown in the accompanying figure. Establish a criterion for the selection of light and stiff materials for this bar (Hints: You need to develop an expression for the mass of material required in terms of tension, bar length, density, and stiffness of the material). M
Case Study Calculate the Tensile Toughness Tensile toughness measures the total energy absorbed prior to fracture and is different from fracture toughness and impact toughness. Fracture toughness measures the resistance to fracture when a flaw (i.e. crack) is present in the material. Since it is nearly impossible and costly to manufacture materials with zero or near zero defects, fracture toughness is a major consideration for all structural materials. Impact toughness measures a materials ability to withstand an impact blow (i.e. high strain rates) and is particularly important in assessing the ductile-to-brittle transition behavior (more details later). Impact toughness is also commonly referred to as notch toughness. The tensile toughness can be estimated using the stress-strain curve by measuring the area under the curve (both the elastic and plastic regions). Tensile Toughness = f Stress, σ Ty- Ey Efracture ETS Ur Ey Efracture o de = U₁ + SETS o de + Sefracture o de Ey Ey o de =…
If the constraint for a design requires a minimum stiffness of E=100 GPa and the design objective is to maximize the material index M E/p, which will you choose betwoen titanium alloys and CFRP? Justify your answer.
INTAKE TUT Air Inlet to search COMPRESSION Combustion Chambers COMBUSTION Turbine EXHAUST
Please answer the question with steps An unknown material bar having length of 4.3m has 1m cross sectional area. One end is in contact with 373K Thermal conductivity of the material is 197W/mK. The total rate of heat flow is Joules/second. ....... .... (Calculate up to one decimal point accuracy).
The stress for low alloys steel at which plastic deformationbegins Is 475 MPa, and the modulus or elastlcity ls 315 PA What is the maximum load that may be applied to a specimenwith a eras sectional area of 300 mm2 without plastic deformed If the original specimen length is 120 mm what is the maximumlength to with may be stretched without causing plastic deformation?
Tensile and fully reversed loading fatigue tests were conducted for a certain steelalloy and revealed the tensile strength and endurance limit to be 1200 and 550 MPa,respectively. If a rod of this material supply were subjected to a static stress of 600MPa and fully-reversed oscillating stresses whose total range was 700 MPa. Assuming garber relationship will this rod fail by fatigue failure