(a)Borosilicate glass bottles are processed into bottles using press and blow method shownTemperature ("F)in Figure 6(a). By referring to Figure 6(b),40080012001600 2000 2400 2800 320010181016Borosilicatei.State the suitable temperature range for making glass bottles and justify theglass96% silicaFused1016glasssilica1014Strain pointanswer.10141012Annealing point10121010H1010ii.Discuss the process to relieve thermal stresses the glass bottles using Figure 6(b).10Softening point10106Working range10510i1i.Briefly discuss the consequence if the process in (ii) is not performed on the glassWorking point1010bottles.Melting point102Soda-lime glass2004006008001000 1200 1400 1600 1800Temperature ("C)iv.State THREE (3) reasons why glass would be the best material for the glass(a)(b)bottles?Figure 6. (a) Press and blow method and (b) temperature dependence of viscosity forvarious types of glassesViscosity (Pa-s)Viscosity (P)

Blow moulding is the process of inflating or blowing a thermoplastic molten tube termed a…

Borosilicate glass bottles are processed into bottles using press and blow method shown in Figure 6(a). By referring to Figure 6(b), i. State the suitable temperature range for making glass bottles and justify the answer. ii. Discuss the process to relieve thermal stresses the glass bottles using Figure 6(b). iii. Briefly discuss the consequence if the process in (ii) is not performed on the glass bottles.

Borosilicate glass bottles are processed into bottles using press and blow method shown in Figure 6(a). By referring to Figure 6(b), i. State the suitable temperature range for making glass bottles and justify the answer. ii. Discuss the process to relieve thermal stresses the glass bottles using Figure 6(b). iii. Briefly discuss the consequence if the process in (ii) is not performed on the glass bottles.

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Question Seven (a) For refractory ceramic materials, cite two characteristics that improve with and two characteristics that are adversely affected by increasing porosity. (b) Show that the minimum cation-to-anion radius ratio for a coordination number of 4 is 0.225. (Hint: Use the AX crystal structure, assuming the anion spheres touch in plane). (c) The unit cell for Al>Os has hexagonal symmetry with lattice parameters a = 0.4759 nm and c 1.2 nm. If the density of this material is equal to 3.99 g/cm' and is calculated according to the formula n'(E Ac+ EAA) V.NA Calculate the atomic packing factor for Al>O, given that the ionic radius for AI is 0.053 nm and i 0' is 0.140 nm. Take N, = 6.023 x 1023 atoms/mole. (d) Mention any three industrial ceramics and indicate their applications.
(a) Following is the Super Asia plastic body washing machine. You are asked to write itsmanufacturing process for the highlighted zone. Draw and label the complete diagram forthat process. Write your reason why you have adopted particularly that manufacturingprocess (b) If the portion of washing machine on the above said picture is metallic then how will yourmanufacturing process change. Draw and label the new manufacturing method.
Question a Cood wetting of the solid bby the liquid is a fundameotal tequirement for iquid phase sintering Considering the lgure given below, ower the following questions liquid solid solid grain boundary dihedral angle Calculate the dihedral angle for a ratio of the interfacial energies Y Yst equal to 1.732 at a particular sintering temperature. How would you describe the microstructure based on your calculation? Answer:
MENG364 MANUFACTURING TECHNOLOGY
Which of the following was NOT done in the synthesis of the thermochromic material? O a. Dissolving the CuCl₂ in absolute ethanol. O b. Placing the beaker in an ice bath for crystallization and collecting the crystals using suction filtration. O c. Immersing the material in an ice bath and back to hot water bath to demonstrate its reversible thermochromism. O d. All of the above statements were done
5
Can you explain the kinetics of recovery, recrystallization, and grain growth? (Draw three plots showing the kinetics of each prosess and explain the plot)
Denive am txpuession for hent transfer de for 1 Sotherma/ 6 admbatic presS e polyhopíc precas.r-n process
It has been found that 'pyrex' cookware made of borosilicate glass does not shatter during baking or cooking around 300°F. However, shattering of cookware made of soda-lime-silicate glass was frequently reported during the years 2012-2013. Find and explain the possible reasons for cookware shattering. Show your calculation. Assume that the cookwares are free of pores, cracks, and scratches. Given: Material/properties Borosilicate Soda-lime-silicate glass glass Thermal expansion coefficient (x106/°C) Elastic modulus (GPa) Failure stress (MPa) 3 9. 62 68 30 30
2. The dameter of a bar abricaled from an allay wlth properties showa in figure below redaced fromm an inltial 1.2 in to a 1.0 In diameler, to a final 1.8 in. diameter. For parts a, b. and when using the graph, you can ignore the marked paints A. B. C, and O 0) Determine the % CW nfter the first step of the process b) Determine the yield stress (in ksi) after the first step of the process t) Determine the % CW after the second step of the proces 22 Tensile srengin (ks 20 18 Yicld strength s) 16 14 10 Elongatie () Percent cold ssok
A 30% ethylene glycol solution in water is gradually cooled. At what temperature in degree celsius does crystallization begin?