5. Name a testing method performed to check standard tightness of tower bolts. 6. This is a document laminated and installed at the ACPDB door cabinet to check electrical loading, 7. What are the number of days after pouring should the concrete reach its required 70% and 100% compressive strength and tested by third party testing center? 7th and 14th day 7th and 21th day 7th and 28th day 14th and 28th day 8. This is a testing method performed to check overall straightness of the tower. 9. What is the maximum value for earth or grounding resistance test? 10. What do you call device/tool used for measuring the galvanization or coating of grounding and tower materials?

5. Name a testing method performed to check standard tightness of tower bolts. 6. This is a document laminated and installed at the ACPDB door cabinet to check electrical loading, 7. What are the number of days after pouring should the concrete reach its required 70% and 100% compressive strength and tested by third party testing center? 7th and 14th day 7th and 21th day 7th and 28th day 14th and 28th day 8. This is a testing method performed to check overall straightness of the tower. 9. What is the maximum value for earth or grounding resistance test? 10. What do you call device/tool used for measuring the galvanization or coating of grounding and tower materials?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Write three aggregate properties that affect compressive strength of concrete.
6.32 The results of an experiment to evaluate the effects of a water reducer are shown in Table P6.32. a. Calculate the water-cement ratio in each of the three cases. b. Using water reducer, how can we increase the compressive strength of concrete without changing workability? Refer to the appropriate case in the table. Chapter 6 Portland Cement, Mixing Water, and Admixtures c. Using water reducer, how can we improve workability without changing the compressive strength? Refer to the appropriate case in the table. d. Using water reducer, how can we reduce cost without changing workability or strength? (Assume that the cost of the small amount of water reducer added is less than the cost of cement.) Refer to the appropriate case in the table. e. Summarize all possible effects of water reducers on concrete. TABLE P6.32 Without Water Reducer With Water Reducer 735 368 2 4,100 Case 1 Case 2 Cement content, lb/yd³ Water content,* lb/yd³ Slump, inches 28-Day compressive strength, psi *Assume…
A concrete masonry unit has actual gross dimensions of 190 mm X 190 mm X190 mm. The unit is tested in a compression machine with the followingresults:Maximum failure load = 370 kNNet volume = 5125 cm3a. Is the unit categorized as solid or hollow? Why?b. Calculate the gross area compressive strength.c. Calculate the net area compressive strength.
2. You are an inspector on a job site, inspecting strength tests from a job with a design strength of 4500 psi. A total of 12 tests were performed on concrete from this job; the strength test results (in psi) are shown below. 4520 4840 4190 4960 4720 4890 4620 4290 4390 4680 4550 4620 Is this concrete acceptable?
Two 150 mm x 300 mm concrete cylinders with randomly oriented steel fiber contents of 0 and 2% by weight, respectively. After curing for 28 days, the specimens were subjected to increments of compressive loads until fail- ure. The load versus deformation results were as shown in Table P7.45. TABLE P7.45 Specimen no. 2 Fiber content (%) 2 Deformation (mm) Load (kN) 0.0305 507 507 0.0610 645 (failure) 681 0.0915 578 0.0915 396 1.525 338 (failure) Assuming that the gauge length is the whole specimen height, determine the following: a. The compressive stresses and strains for each specimen at each load increment. b. Plot stresses versus strains for the two specimens on one graph. c. The initial modulus of elasticity for each specimen. d. The ultimate strength for each specimen. e. The strain at failure for each specimen. f. Toughness. Curves may be approximated with a series of straight lines. g. Comment on the effect of adding fiber on the following: i. Modulus of elasticity ii. Ultimate…
A project requires a compressive strength of 3500 psi. The 3-day test showed an average strength of 1256 psi and the Z day test showed an average strength of 2047 psi. Calculate the projected 28-day strength of the concrete. Will it meet the specs? Ans: 3 days is 1256pri (407) 21 40
An ASTM indicator of workability when evaluating freshly mixed Portland cement concrete. Choices: - C143 - C187 - C191 - C496
Briefly describe how super high strength concrete (f’c = 15,000 psi) can be made
1) What is the recommendations of Density, Absorption and Voids in Hardened Concrete lab test? 2) What is the errors that might happen on this lab test and how to prevent it? Recommendations for at least 4 industrial applications with details provided. do it academically and Do not copy, write it as a points