In order to evaluate the sustainability of non-potable water available in the job site for mixing concrete, six standard mortar cubes were made using that water and six others using potable water. The cubes were tested for compressive strength after 7 days of curing and produced the loads to failure (in kN) shown in table below. Based on these results, would you accept that water for mixing concrete?

In order to evaluate the sustainability of non-potable water available in the job site for mixing concrete, six standard mortar cubes were made using that water and six others using potable water. The cubes were tested for compressive strength after 7 days of curing and produced the loads to failure (in kN) shown in table below. Based on these results, would you accept that water for mixing concrete?

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Subject: concrete technology Note: provide detailed answer 1- What is the difference between an additive and an admixture? 2- Which cement would you not use with calcium chloride? 3- Explain the mechanism of action of retarders? 4- What are the advantages of using calcium chloride with Portland cement concrete?
Three batches of concrete were prepared using the same materials and ingre- dients, except that they have water-cement ratios of 0.50, 0.55, and 0.60, respectively. The following tests were performed on specimens made of the three batches: - Compressive strength test on 100 mm × 200 mm cylinders - Center point floxure test on 100 mm × 100 mm × 300 mm bcams - Split tension test on 150 mm X 300 mm cylinders Three replicates were tested for each test. Table P7.38 shows the average fail- ure loads for the three replicates of each case. It is required to do the following: a. Complete Table P7.38 b. Using an Excel sheet, plot the relationships between water-cement ratio and compressive strength, modulus of rupture, and tensile strength on the same graph. Label all axes and curves. c. Comment on the effect of water-cement ratio on the compressive strength, modulus of rupture, and tensile strength. TABLE P7.38 w/c Ratio Compressive Strength Test Flexure Test Split Tension Test Compres- sive…
7.43 Three batches of concrete were prepared using the same materials and ingre- dients, except that they have water-cement ratios of 0.50, 0.55, and 0.60, respectively. The following tests were performed on specimens made of the three batches: Compressive strength test on 100 mm × 200 mm cylinders · Center-point flexure test on 100 mm × 100 mm × 300 mm beams Split tension test on 150 mm × 300 mm cylinders Three replicates were tested for each test. Table P7.43 shows the average fail- ure loads for the three replicates of each case. It is required to do the following: a. Complete Table P7.43 b. Using an Excel sheet, plot the relationships between water-cement ratio and compressive strength, modulus of rupture, and tensile strength on the same graph. Label all axes and curves. c. Comment on the effect of water-cement ratio on the compressive strength, modulus of rupture, and tensile strength. Questions and Problems 351 TABLE P7.43 w/c Ratio Compressive Strength Test Flexure Test Split…
a design engineer has specified a concrete strength of 4400 psi. the ready mixed concrete producer has a plant standard deviation of 260 psi. what is the required average strength for the concrete?
2. What is the standard size of PCC specimens to be tested for compressive strength? If a smaller size is used, which size is expected to provide higher compressive strengths? Why? Which size provides strengths close to that of an actual concrete structure? 3. What is the purpose of performing the flexure test on concrete? How are the results of this test related to the compressive strength test results? 4. What are the advantages of using a third-point loading flexure test over a center-point loading flexure test? Draw a shear force diagram and a bending moment diagram for each case to support your answer.
Two batches of concrete cylinders were made with and without a calcium chloride (CaCl2) accelerator admixture. Six cylinders were made of each batch and submerged in water for different times before testing for compressive strength and the results are shown in Table P6.34. It is required to do the following: a. Using an Excel sheet, plot the relationship between curing time and compressive strength of the two mixes on the same graph. Label all axes and curves. b. Comment on the effect of the accelerator on the compressive strength of PCC at early and late ages. TABLE P6.34 Cylinder no. 1 2 3 4 5 6 Water submergence (days) Compressive strength of plain concrete (MPa) Compressive strength of concrete with accelerator (MPa) 1 3 7 14 21 28 0.8 7.8 15.8 21.1 24.5 26.8 6.2 14.8 20.1 24.0 25.9 26.8
Working on major construction project that requires considerable amounts of concrete to be used,you are asked to design a concrete mix following the BRE methodology. All the necessary tables forthis can be found in the Appendix. The concrete mix specifications are:o Characteristic compressive strength of 35 N/mm 2 at 28 days.o Failure rate of 2%o Previous control data yielded a standard deviation of 10 N/mm 2o CEM-I 42.5o Air-entraining is not requiredo Maximum water to cement ratio 0.40o Minimum cement content 390 kg/m 3o Required slump 50 mmo Coarse aggregate: Crushed maximum size 20mmo Fine aggregate: Uncrushed with 90% passing 600 μm sieveo Relative density of aggregates: 2.5o Coarse aggregate has 4% moistureo Fine aggregate is dry and has 1.2% absorption.o Volume of the required trial mix: 0.090 m 3Following the BRE step-by-step process estimate the water content of the mix estimate the content of aggregates, provide the estimated mix quantities
A concrete test cylinder with a cross-sectional area of 28.3 in squared is to be tested in axial compression. Before loading two marks are scribed on the cylinder precisely 8 in apart (as shown in the figure below) when the load is 40,000 lb the marks are measured and found to be 7.997 in apart determine the E value for this concrete. Assume an approximately linear relationship between stress and strain.
True or false: Generally speaking, concrete will be priced the same regardless of its designed strength, 4,500 psi concrete will cost the same as 3,000 psi concrete.
Students in the materials class prepared three mortar mixes with water to cement ratios. Three 6cm mortar cubes were prepared for each mix. The cubes were cured for 7 days and then tested for compressive strength in Pa. The test results were as shown. Water cement Ratios are 0.40, 0.50 and 0.60 for mix 1, 2 and 3 respectively. Determine the following:a. The compressive strength of each cube. (in Pa)b. The average compressive strength for each mix ( in Pa)