Theory of Structures Calculate all the member forces for the truss given in the figure below,By method of section TheoryExample (3): Calculate all the member forces for the truss given in the figure below.How30KN3m4m

Answered: Theory of Structures Calculate all the…

Engineering

Civil Engineering

Theory of Structures Calculate all the member forces for the truss given in the figure below, By method of section

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Statics of Rigid Bodies (Truss Analysis) answer should in 4 decimal places
The members of a plate structure shown in the figure can be a bar in this sense Which are connected by a joint and thus form a truss or beam type that to Stiff faces are joined together to form a frame. In the frame option rotate the connected nodes The wall may be free or closed. Differences in displacement and stresses in structural members Examine truss models and fab models, assuming all members have a square cross section with dimensions b=15 and H = 120 mm L = 160mm The load is P = 1.0N KL L-
The state of stress at a critical section is shown in Fig. Determine the state of stress on the element inclined at an angle of 30° clockwise from the x-axis. Represent these stresses on the element. 50 MPa - 100 MPa 25 MPa
Problem 1: 20 ft 20 ft 5 k Determine the loadings at the each member of the frame shown in the figure. I = 500 in 4 A = 10 in ² E = 29 x 10³ ksi
HW2: Analyze the truss shown in the figure, EA is constant for all members 4 m 4 m D 50 kN 3 m E A FI 100 kN
Problem 5 Rigid bar ABCD shown in the figure is supported by a smooth pin at D and by vertical aluminum alloy [E = 10,000 ksi] bars attached at joints A and C. Bar (2) was intended to have a length of 60 in.; however, its actual length after fabrication was found to be L2= 59.88 in. To connect it to the pin at C on the rigid bar, bar (2) will need to be manually stretched by A = 0.12 in. After bar (2) has been stretched and connected to the pin at C. Use the following additional properties and dimensions: A1 = A2 = 0.75 in², Determine: (a) the normal stresses in bars (1) and (2). (b) the deflection at A of the rigid bar. (1) 40 in 36 in Rigid bar 54 in P-20kips (2) L₂ 48 in D
kk.242.
The rigid bar of negligible weight is supported as shown in the figure. If W = 104 kN, compute thetemperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data:
A steel strut S serving as a brace for a boat hoist transmits a compressive force P = 63 kN to the deck of a pier as shown in the figure. The strut has a hollow square cross section with wall thickness t = 8 mm and the angle θ between the strut and the horizontal is 41°. A pin through the strut transmits the compressive force from the strut to two gussets G that are welded to the base plate B. Four anchor bolts fasten the base plate to the deck. The diameter of the pin is dpin = 19 mm, the thickness of the gussets is tG = 14 mm, the thickness of the base plate is tB = 10 mm, and the diameter of the anchor bolts is dbolt = 10 mm. Determine the bearing stress between the anchor bolts and the base plate in MPa.
Using the force (flexibility/compatibility) method, analyse the structure in the figure below: A B ΕΙ C
A solid steel bar of diameter di = 1.3 in. is enclosed by a steel tube of outer diameter dz = 2.45 in. and inner diameter d2 = 1.95 in. (see the figure). Both bar and tube are held rigidly by a support at end A and joined securely to a rigid plate at end B. The composite bar, which has length L = 29 in., is twisted by a torque T = 4,900 lb-in. acting on the end plate. Tube B Ва End plate (a) Determine the maximum shear stresses Tį and T2 in the bar and tube, respectively. Round your answers to the nearest whole number. T1 = psi T2 = psi (b) Determine the angle of rotation (in degrees) of the end plate, assuming that the shear modulus of the steel is G = 11.4 x 10° psi. Round your answer to three decimal places. (C) Determine the torsional stiffness kr of the composite bar. Round your answer to the nearest whole. [Hint: Use equations below to find the torques in the bar and tube.] GIP, T1 = T (G,Ip + G2IP, kT = k-in.
A tapered bar with varying diameter 1.5 d to d is subjected to tensile force of magnitude 1000 N. The Young's modulus of elasticity of the material is E = 160 GPa, length of bar 1 = 2 m, d = 20 mm. The extension caused by tensile load. A 0.026 mm B 0.039 mm C 0.052 mm D 0.043 mm