Answered: 6 ft 6 ft 6 ft 400 lb 400 lb 400 lb 400…

Engineering

Civil Engineering

6 ft 6 ft 6 ft 400 lb 400 lb 400 lb 400 lb 400 lb F 200 lb 200 lb D G 9 ft B K A C E Н 3 ft 9 ft- 9 ft- 6 ft 6 ft 6 ft

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

1. For the roof truss shown in Figure 3, determine the force present in ele- ment GH and in each element located to the right of GH. Also, establish whether the elements are in tension or compression. (I suggest you start from node M applying the method of nodes until you get to element GH) -2.4 m--2.4 m-1.2 m-2.4 m--2.4 m--1.2 m- 1.5 kN 1.5 kN 1.5 kN 1.5 kN D VI 1.5 kN 1 kN В 2.5 m E K 1 kN 1m H M F
Determine (approximately) the forces in the members of the truss shown below. Show your solution including units and the free body diagrams. 20 KN F 3 m A 10 kN 4 m E 20 KN 4 m D C 10 KN
KINDLY DRAW THE FDB AND SHOW IN THE DRAWING THE DEFLECTION. PLEASE DRAW THE FBD OF DEFLECTION POINTS
Need answer fast.
analysis the truss using method of joints to find the internal forces. by steps please.
• In the following problems solve the value of internal force member in the truss using the method of Section or the method of Joint • Show the free body diagram (FBD) in your solution • Solving without any FBD in your solution is considered wrong. • State whether each member is in TENSION (T) or COMPRESSION (C)
NOTE: This is a multi-part question. Once an answer is submitted, you will be unable to return to this part. A roof truss is shown. Take the load P = 1.7 kN. Determine the force in each member of the roof truss shown. State whether each member is in tension (T) or compression (C). Note: please double check answers. Thanks.
Draw the free body diagram. Do not round off between your solutions and box your final answer up to 4 decimal places
1. For the roof truss shown in Figure 3, determine the force present in ele- ment GH and in each element located to the right of GH. Also, establish whether the elements are in tension or compression. (I suggest you start from node M applying the method of nodes until you get to element GH) -2.4 m--2.4 m-1.2 m-2.4 m--2.4 m--1.2 m- 1.5 kN 1.5 kN 1.5 kN 1.5 kN D VI 1.5 kN 1 kN В 2.5 m E Ук 1 kN 1m H F Figura 3. Cercha 3. 2.Determine the force in the elements ED, EH, and GH of the reinforcement (see Figure 4), and establish whether the elements are in tension or compres- sion. (Use the method of sections). Figura 4. Cercha 4. 50 kN 40 kN -2 m -2 m- -2 m- 1.5 m -30 kN 1.5 m B 40 kN 1.5 m
View Policies Current Attempt in Progress Determine the force in each member of the loaded truss. The force is positive if in tension, negative if in compression. Answers: AB= AC = i i IM BC= i 69° 14° 45° W B W W W
In the following problems solve the value of internal force member in thetruss using the method of Joint. Show the free body diagram (FBD) in every joint you solve. State whether each member is in TENSION (T) or COMPRESSION (C)
Problem 2: Determine the forces in all diagonal and horizontal members of the truss shown below using the method of sections. Determine the force in all vertical members using the method of joints. Hint, the structure is symmetric. The distributed load is transferred to the truss from the roof purlins. State whether the members are tension or compression. Summarize your results on a sketch of the truss. 2.5 k/ft H M K 12 ft A G B C D F 6 @ 12 ft = 72 ft