The aluminum bar ABC has a cross-sectional area of 20 mm2 is supported by a pin at A and a steel wire at B. If P = 50 kN calculate the horizontal displacement of P. The cross-sectional area of the wire is 1.5 mm2, modulus of elasticity of aluminum is 70 GPa and the modulus of elasticity of steel is 200 GPa. 90 cm B 90 cm 200 cm 120 cm

The aluminum bar ABC has a cross-sectional area of 20 mm2 is supported by a pin at A and a steel wire at B. If P = 50 kN calculate the horizontal displacement of P. The cross-sectional area of the wire is 1.5 mm2, modulus of elasticity of aluminum is 70 GPa and the modulus of elasticity of steel is 200 GPa. 90 cm B 90 cm 200 cm 120 cm

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Solve the following problem and SHOW YOUR COMPLETE SOLUTIONS. ILLUSTRATE A FREE BODY DIAGRAM FOR BETTER UNDERSTANDING
Two polymer bars are connected to a rigid plate at B, as shown. Bar (1) has a cross-sectional area of 1.2 in.2 and an elastic modulus of 1820 ksi. Bar (2) has a cross-sectional area of 1.185 in.2 and an elastic modulus of 3590 ksi. Assume L1=21 in., L2=48 in., Q=7.6 kips, P=2.6 kips, and R=12.8 kips. Determine the horizontal deflection of end C relative to end A.
The pin-connected structure shown in the figure consists of a rigid beam ABCD and two supporting bars. Bar (1) is a bronze alloy [E = 91 GPa] with a cross-sectional area of A1 = 230 mm2. Bar (2) is an aluminum alloy [E = 70 GPa] with a cross-sectional area of A2 = 730 mm2. All bars are unstressed before the load P is applied; however, there is a 4-mm clearance in the pin connection at A. Assume L1 = 1660 mm, a = 950 mm, b = 550 mm, c = 410 mm, and L2 = 1230 mm. If a load of P = 176 kN is applied at B, determine (a) the normal stresses in both bars (1) and (2). (b) the downward deflection of point A on the rigid bar.
Problem 5 Rigid bar ABCD shown in the figure is supported by a smooth pin at D and by vertical aluminum alloy [E = 10,000 ksi] bars attached at joints A and C. Bar (2) was intended to have a length of 60 in.; however, its actual length after fabrication was found to be L2= 59.88 in. To connect it to the pin at C on the rigid bar, bar (2) will need to be manually stretched by A = 0.12 in. After bar (2) has been stretched and connected to the pin at C. Use the following additional properties and dimensions: A1 = A2 = 0.75 in², Determine: (a) the normal stresses in bars (1) and (2). (b) the deflection at A of the rigid bar. (1) 40 in 36 in Rigid bar 54 in P-20kips (2) L₂ 48 in D
Show complete solution please.
The rigid bar of negligible weight is supported as shown in the figure. If W = 104 kN, compute thetemperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data:
I need to solve the question of strength materials
The rigid bar of negligible weight is supported as shown in the figure. If W = 80 kN, compute the 2 temperature change of the assembly that will cause a tensile stress of 50 MPa in the steel rod. Use the following data: A (in) a (PF) E (GPa) Steel Rod 300 11.7 x 104 200 Bronze Rod 1400 18 x 106 83 Bronze 3 m Steel 1.5 m 1.0 m 2.5 m 1.5 m W
The nut on a bolt is tightened by applying a force of P = 38 lb to the end of a wrench at a distance of a = 6.0 in. from the axis of the bolt. The body of the bolt has an outside diameter of d = 0.425 in. What is the maximum torsional shear stress in the body of the bolt?
L = 2.75
A steel rod is rigidly attached between an aluminum and bronze rod. The diameters of eachmaterial are shown in the figure. A fixed support is rigidly attached to the right end of thebronze rod. Determine the stress each section in KPa.
A tapered bar with varying diameter 1.5 d to d is subjected to tensile force of magnitude 1000 N. The Young's modulus of elasticity of the material is E = 160 GPa, length of bar 1 = 2 m, d = 20 mm. The extension caused by tensile load. A 0.026 mm B 0.039 mm C 0.052 mm D 0.043 mm