Problem 6The zero-, positive-, and negative-sequence bus impedance matrices for a three-bus three-phasepower system are:[0.10Zbus 0 = j0.20per unit0.10[0.12 0.08 0.04Zbus 1 = Z bus 2 = j|0.08 0.12 0.060.04 0.06 0.08The prefault voltage is 1.0Determine the per-unit fault current and per-unit voltage at bus 2 for:per unit.a) A bolted three phase fault at bus 1b) A bolted single line-to-ground fault at bus 1.c) A bolted line-to-line fault at bus 1.d) A bolted double line-to-ground fault at bus 1.

We are authorized to answer three subparts at a time. Since you have not mentioned which part you…

The zero-, positive-, and negative-sequence bus impedance matrices for a three-bus three-phase power system are: r0.10 0. Zbus 0 = j 0.20 per unit 0.10 [0.12 0.08 0.04 Zbus 1 = Z bus 2=j0.08 0.12 0.06 0.04 0.06 0.08 The prefault voltage is 1.0 per unit. Determine the per-unit fault current and per-unit voltage at bus 2 for: a) A bolted three phase fault at bus 1 b) A bolted single line-to-ground fault at bus 1. c) A bolted line-to-line fault at bus 1. d) A bolted double line-to-ground fault at bus 1.

The zero-, positive-, and negative-sequence bus impedance matrices for a three-bus three-phase power system are: r0.10 0. Zbus 0 = j 0.20 per unit 0.10 [0.12 0.08 0.04 Zbus 1 = Z bus 2=j0.08 0.12 0.06 0.04 0.06 0.08 The prefault voltage is 1.0 per unit. Determine the per-unit fault current and per-unit voltage at bus 2 for: a) A bolted three phase fault at bus 1 b) A bolted single line-to-ground fault at bus 1. c) A bolted line-to-line fault at bus 1. d) A bolted double line-to-ground fault at bus 1.

Introductory Circuit Analysis (13th Edition)

13th Edition

ISBN:9780133923605

Author:Robert L. Boylestad

Publisher:Robert L. Boylestad

Chapter1: Introduction

Section: Chapter Questions

Problem 1P: Visit your local library (at school or home) and describe the extent to which it provides literature...

See similar textbooks

Related questions

Q: Q3: For the transmission-generator, system shown in figure below, the bus impedance matrix (in per…

A: Given Data:A three-phase symmetrical fault occurring at the bus 1 with,Fault impedance Bus impedance…

Q: A fault occurs at bus 4 of the network shown in Figure Q3. Pre-fault nodal voltages throughout the…

A: x=1y=7Note: reactance of element right to bus 4 is not given. Hence we will not consider that in…

Q: For the power system shown at right the impedance matrix (2 is j0.4 3 j0.5 j0.2 0.164 0.101 0.0692…

Q: A three-phase fault with a fault impedance Zf = j0.16 per unit occurs at bus 3 in the Figure beside,…

A: The answer is 2. Please fill answer only 2.

Q: A three-phase, Y-connected, 75-MVA, 27-kV synchronous generator has a synchronous reactance of 9.0 2…

A: The given data is shown below:

Q: jX, (1) 2 3x. iX; E, O E. Figure 1

A: Three phase short circuit occur at bus 2 a) Calculating sub transient generator current Ig…

Q: The positive-sequence reactances for the power system shown below are in per unit on a common MVA…

A: It is given that:

Q: Considering two parallel three-phase circuits that are close together, when calculating the…

A: whether the mutual coupling effects are significant enough to be included in the calculations or if…

Q: Compare load flow per unit and fault level analysis main purposes? What is the difference?

A: step-1-> Both load flow per unit analysis and fault level analysis are crucial methods used in…

Q: b) A fault occurs at bus 2 of the network shown in Figure Q3. Pre-fault nodal voltages throughout…

Q: For the following power system, all bus voltages are initially 1 1 pu. Then a three-phase fault…

A: The reactance diagram of the given system will be After a 3-phase fault, the fault point will be…

Q: Please answer this diligently. Other answers in the internet seems wrong. Please help me understand…

A: First, we need to calculate the base current. The base current (Ibase) can be calculated using the…

Q: For the three-bus system shown in figure below: • The line from bus 1 to bus 2 has an imped- ance Z…

A: The objective of the question is to write the real and reactive power balance equations for bus 3 in…

Q: j0.2 For the following power system the impedance matrix is given below. Initially all bus voltages…

Concept explainers

Fault Analysis

In an electrical engineering system, a fault is an abnormal electric current flowing through the system, and fault analysis is the study of these faults. For instance, a short-circuit is a fault where the live wire touches the ground or neutral wire. If a circuit is interrupted by a failure of a current-carrying wire then an open circuit fault occurs. The open-circuit faults are also called series faults. One or more phases or ground may be involved in a three-phase fault or may occur only between two phases. Current flows into the earth in case of a ground fault or earth fault. For most situations, the prospective short circuit current of a fault that is predictable can be calculated. To limit the loss of service because of a failure, the protective devices can detect fault conditions and operate circuit breakers and also other devices. All phases equally can be affected in a poly-phase system which is known as symmetric electrical fault. The asymmetric fault becomes more complicated to analyze if only some phases are affected. By using methods such as symmetrical components, the power system analysis of these types of faults is often simplified. The main objective of power system protection is to design, detect, and interrupt power system faults.

Question

Problem 6
The zero-, positive-, and negative-sequence bus impedance matrices for a three-bus three-phase
power system are:
[0.10
Zbus 0 = j
0.20
per unit
0.10
[0.12 0.08 0.04
Zbus 1 = Z bus 2 = j|0.08 0.12 0.06
0.04 0.06 0.08
The prefault voltage is 1.0
Determine the per-unit fault current and per-unit voltage at bus 2 for:
per unit.
a) A bolted three phase fault at bus 1
b) A bolted single line-to-ground fault at bus 1.
c) A bolted line-to-line fault at bus 1.
d) A bolted double line-to-ground fault at bus 1.

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

This is a popular solution!

SEE SOLUTION Check out a sample Q&A here

Step 1

Step 2

Step 3

Step 4

Step 5

Trending now

This is a popular solution!

Step by step

Solved in 5 steps with 2 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, electrical-engineering and related others by exploring similar questions and additional content below.

Similar questions

Figure below shows the single-line diagram of three-bus power system with generation at bus 1 and bus 3. The voltage at bus 1 is V₁ = 1.025/0° per unit. The voltage magnitude at bus 3 is fixed at 1.05 per unit with a real power generation of 250 MW. The scheduled load on bus 2 is marked on the diagram. Line impedances are marked in per unit on a 100 MVA base. Line resistances and line charging susceptances are neglected. By using Gauss-Seidel method and initial estimates of V₂(0) = 1.020° and V3(0) = 1.0520°, determine V₂ and V3. Perform calculation for one iteration. V₁ = 1.025/0° j0.1 Slack Bus j0.2 j0.4 j0.2 3 j0.1 250 MW 150 Mvar |V3|=1.05 P3 = 250 MW
The bus impedance matrix for a three-bus power system has per-unit elements as: Z11 = 0.5 Z12 = 0.4 Z13 = 0.8 Z21 = 1 Z22 = 0.5 Z23 = 0.6 Z31 = 0.5 Z32 = 1.2 Z33 = 1 Prefault voltage is 1 per unit and prefault current is neglected. A three-phase short circuit occurs at bus 3. Determine the subtransient fault current. Round your answer to 2 decimal places.
Refer to the 5-bus data given below. Sbase = 400 MVA, the base voltage is 15.0 kV for buses 1 and 3, and 345 kV for buses 2, 4, 5. Note that 1-5 and 3-4 are 15/345 kV transformers.a) Draw a one-line diagram of the power system.b) Find the elements Y23, Y43, Y11 Y33 of the system bus admittance matrix.
A three-bus power system has generators at buses 1 and 2 with per unit subtransient reac- tances G1X"=0.1 and G2X"=0.08. The per unit branch reactances are X12=0.05, X13=0.10, X23=0.05, with 0.0540 0.0368 0.0425 Zbus = j 0.0368 0.0506 0.0460 0.0425 0.0460 0.0782 The pre-fault voltage magnitude is 1.02 per unit and the system is unloaded. Suppose a three-phase fault occurs at bus 3. (a) Calculate the fault current I" at the faulted bus. (b) Calculate the per unit generator terminal voltages (V1, V½) during the fault. (c) Calculate the per unit line currents feeding bus 3 (I13, I23) during the fault.
Solve numerical : Following figure shows the one-line diagram of a two bus system. Take bus 1 as slack bus, bus 2 as load (PQ) bus. Neglect the shunt charging admittance. Obtain the bus admittance matrixYBUS and find V2 and δ2, power flows and line losses by using Fast decoupled power flow method. All the values are given in per unit on 100MVA base. Use a tolerance of 0.001 for power mismatch.