The width of the expansion joint is20mm in a cement concrete pavement.The laying temperature is 20 °C and themaximum slab temperature in summeris 60 °C. The coefficient of thermalexpansion of concrete is 10 x 10-6 mm/mm / °C and the joint filler compressesupto 50% of the thickness. The spacingbetween expansion joints should be

Given data: Width of expansion joint = 20 mm The joint filler compresses upto 50 % Compression of…

The width of the expansion joint is 20mm in a cement concrete pavement. The laying temperature is 20 °C and the maximum slab temperature in summer is 60 °C. The coefficient of thermal -6 expansion of concrete is 10 x 10⁰ mm/ mm / °C and the joint filler compresses upto 50% of the thickness. The spacing between expansion joints should be

The width of the expansion joint is 20mm in a cement concrete pavement. The laying temperature is 20 °C and the maximum slab temperature in summer is 60 °C. The coefficient of thermal -6 expansion of concrete is 10 x 10⁰ mm/ mm / °C and the joint filler compresses upto 50% of the thickness. The spacing between expansion joints should be

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

Standard deviation is 3.6 MPa
Hardening of concrete is caused by "Hydration" True False
Answer by true or false for the following If the number of the crushed particles in the fractured concrete is high, this means that the strength of aggregate is lower than the compressive strength of concrete. a- True b- False
Correct and complete solution please
Reinforced concretes are usually attacked by water and rusted. This is due to, a. Low density cements or high porosity that allow water to reach the steel b. The expansion of the rust as it has higher volume than steel push the cement cover and break it c. All the options d. None of the options e. The cover thickness is too small (the steel is too close to the end of the concrete block)
2. The compound bar given in figure, composed of the three segments shown, is initially stress free. Compute the stress in each material if the temperature drops 25 °C. Assume that the walls do not yield and use the following data: A (mm?) a (1°C) E (GPa) Bronze segment 2000 19.0 x 10-6 83 Aluminum segment 1400 23.0 x 10-6 70 Steel segment 800 11.7 x 10-6 200 800 mm 500 mm– +400 mm→ Aluminum Steel Bronze
The flexural strength (fr) of concrete measured from the bending test is always higher than the direct tensile strength (ft). In reality, the stress in the cracked part of the concrete is lower than ft. Also, failure may occur on the compressive side. Assuming NO tension softening (i.e., the stress in the cracked part stays at ft) and infinite compressive strength (i.e., compressive failure will never occur), draw the stress distribution over the depth of the beam at ultimate failure when the curvature of the section is approaching infinity. With this stress distribution, show that the upper bound of fr/ft is equal to 3. (Hint: On rotating the section, because the compressive stress can increase well beyond ft, the neutral axis will continue to shift upwards.)
The concrete beam shown below is made of an all-lightweight concrete with a unit weight 7=/ 800 kg/ ni a. Compute the value of the cracking moment and b. Estimate the value of the concentrated load P at midspan that causes the beam to crack (include the dead weight of the beam). f, =27.5 MPa 100 mm P=? Wbeam 2-D25 - 5 m 100 mm 100 mm 300 mm
An aluminum pipe is filled in polymer concrete is subjected to a pure compressive force as shown in the figure below. Determine the factor of safety against compressive stress acting on the column. The pipe has an outer diameter of 60 mm and inner diameter of 50 mm. The aluminum and the polymer concrete have the following material properties: Young's modulus: Eal = 70 GPa (aluminum). Ecr = 10 GPa (polymer concrete). Yield compressive strength: Sy-al = 150 MPa (aluminum), Sy-cr= 80 MPa (polymer concrete). 100 kN 500 mm Select one O FS = 6.4 FS= 1.3 o FS =1.1 O FS =1.7 OFS=50
Determine the cracking moment for the figure shown if it is a normal weight concrete with fc=4,000psi. 8 in. 8 in. 24 in. 3 #10 8 in. 3 in.: ⒤갓⒤갓⒤뀐⒤뀐⒤ 6 in. 15 in. -16 in.-
This course EHide blocks An aluminum pipe is filled in concrete is subjected to a pure compressive force as shown in the figure below. Determine the factor of safety against compressive stress acting on the column. The pipe has an outer diameter of 45 mm and inner diameter of 35 mm. The aluminum and the polymer concrete have the following material properties: Young's modulus: Eal = 70 GPa (aluminum), Ecr = 30 GPa (concrete). Yield compressive strength: Sy-al = 180 MPa (aluminum), Sy-cr 60 MPa (concrete). 100 kN 500 mm Select one: O FS = 1.5 O FS = 1.7 O ES- 19 5:45 PM 86°F Light rain ENG 6/18/2021
Estimate the tensile strength required to prevent cracking in a concrete-like material that is cast into a bar, 500 mm long, and is fully restrained at each end against axial movement. The concrete is initially cast and cured at a temperature of 23°C and subsequently cools to a temperature of 10° C. Assume the modulus of elasticity is 32 GPa and the linear coefficient of thermal expansion is 0.00001 m/m/° C.