6. The temperature of concrete for highways reaches 60C in summer, and in winter the temperature drops to (-40C). What is the magnitude of the expansion of a section of highway concrete of 10 m in length when exposed to the highest and highest temperature? Note that the linear expansion coefficient is 2 - deg 12x10-6 (Ans = 12mm)

6. The temperature of concrete for highways reaches 60C in summer, and in winter the temperature drops to (-40C). What is the magnitude of the expansion of a section of highway concrete of 10 m in length when exposed to the highest and highest temperature? Note that the linear expansion coefficient is 2 - deg 12x10-6 (Ans = 12mm)

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Similar questions

If width of the expansion joint is 1.7 m in a cement concrete pavement. The laying temperature is 38°C and the maximum slab temperature in summer is 50°C. The coefficient of thermal expansion of concrete is 4 x 10-5 mm/mm / °C and the joint filler compresses upto 28% of the thickness. The spacing between expansion joints is S mm then Value of S is mm.
Reinforced Concrete
Q2) Layers of Brass, Steel and Aluminum are bonded together and formed section shown below. Cantilever beam is loaded at the tip with 100 kN. In the cross-section height of steel is 50 mm, height of the aluminum is 350 mm and height of the brass is 100 mm. Modulus of clasticity for the materials are given as; Steel, Est = 200 GPa, Aluminum, E = 70 GPa and Brass, Esr= 105 GPa. Find the maximum axial stresses under given loading for Steel, Aluminum and Brass, separately. Steel 150 kN 500 mm 50 mm Aluminum Aluminum 350 mm Brass Brass 100 mm Cross Section of the 5 m Beam Fixed Side view of the Beam Support
The gel space ratio of a concrete sample is given as 589. What is the theoretical strength (N/mm²) of that concrete sample?
A standard brick ( dimensions 200mm x 100mm x 65mm) is compressed lengthwise by a force Pas shown. If the ultimate shear stress for the brick is 8MPA, that occurs at an inclination of 45° with the horizontal, and the ultimate compressive stress is 26 MPa, what is the axial deformation of the brick? Modulus of elasticity of the brick is 2.65 GPa. 200 mm 100 mm 65 mm
Answer by true or false for the following Aggregate is said to be sound when volume changes results in the deterioration of concrete. a- True b- False
At 400-pa the volume was 1-cu.m and then at 3400-pa the volume was 0.990-cu.m calculate the bulk modulus of elasticity of water
A uniform concrete slab is to be attached to two rods whose lowers ends are initially at the same level. What is the required area, in mm², of aluminum rod so that slab will remain level after it is attached to the rods? 4 m Aluminum E = 72 GPa Steel A= 96 mm < E = 200 GPa 4 m 3 m- 0.50 m
Determine the x-bar centroid of the composite figure shown. Where: x=5 ftShow your solution and round off if possible
Please try to solve only part 2 within 20 minute This is request
Situation 5: The compound bar, composed of the three segments shown, is initially stress free. Compute the stress in each material if the temperature drops 25°C. Assume that the walls do not yield and use the following data: A (mm²) a (/*C) E (GPa) Bronze segment 2000 19.0 x 10-6 83 Aluminum segrnent 1400 23.0 x 10-6 70 Steel segment 800 11.7 x 10- 200 - 500 mm→- 400 mm- 800 mm Aluminum Steel Bronze 17. Compute the stress in the bronze bar a. 31.6 MPa (T) b. 31.6 MPа (С) 18. Compute the stress in the aluminum bar. а. 45.1 MPа (Т) b. 45.1 MPa (C) 19. Compute the stress in the steel bar. 79.0MPA (T) 79.0MPA (C) 13.6 MPa (T) 13.6 MPa (C) c. d. 54.1 MPа (Т) 54.1 MPa (C) с. d. a. C. 97.0 MPa (T) b. d. 97.0 MPa (C)
What are harmful manifestations of plastic shrinkage in a) reinforced columns and slab? Assuming that the temperature