Compressive strength developed with the age of hardening and decrease with the increase of water addition to the mix. Whilst, the last one is adversely related with the flexural strength of the concrete. * True False Other:

Compressive strength developed with the age of hardening and decrease with the increase of water addition to the mix. Whilst, the last one is adversely related with the flexural strength of the concrete. * True False Other:

Structural Analysis

6th Edition

ISBN:9781337630931

Author:KASSIMALI, Aslam.

Publisher:KASSIMALI, Aslam.

Chapter2: Loads On Structures

Section: Chapter Questions

Problem 1P

See similar textbooks

Related questions

Q: Once in civil engineering, what is the minimum curing period typically recommended for concrete…

A: In civil engineering, the minimum curing period for concrete structures typically depends on the…

Q: Rate of Tricalcium silicate (C3S) is higher in Type III cement.

A: Given statement: Rate of Tricalcium silicate (C3S) is higher in type III cement. Tricalcium…

Q: choose the correct option please Silica fume admixture increase concrete strength up to 60 MPa 120…

A: This question is related to Concrete technology from Civil Engineering. In this question ask about…

Q: tie bars (in mm, round off to the nearest Tie bars of 12 mm diameter are to be provided in a…

Q: The 70-30 bruss used for a certain application should bave a minimum tensile strength of 50ksi, and…

A: To determine the percentage of cold work required to achieve the specified properties, we can use…

Q: 7. A solid aluminum cylinder is placed within an ASTM A501 steel tube as shown. Compute the stresses…

A: Given Data: The diameter of the solid aluminum cylinder is d1=3 in. The diameter of the steel tube…

Q: T 1. The "slump" test is used to determine the compressive strength of a concrete. F (F 2. For room…

A: Note:- I'm explaining the top three parts here. For all other parts kindly resubmit the question. 1.…

Q: Hydration of cement is due to chemical action of water with * Gypsum Tricalcium aluminate and…

A: Option D is correct...

Q: What is the weakest property of concrete? The compressive strength of the coarse aggregate The…

A: What is the weakest property of concrete?The compressive strength of the coarse aggregateThe…

Question

Compressive strength developed
with the age of hardening and
decrease with the increase of water
addition to the mix. Whilst, the last
one is adversely related with the
flexural strength of the concrete. *
True
False
Other:

Expert Solution

This question has been solved!

Explore an expertly crafted, step-by-step solution for a thorough understanding of key concepts.

SEE SOLUTION Check out a sample Q&A here

Step 1

VIEW

Step 2

VIEW

Step 3

VIEW

Step by step

Solved in 3 steps with 3 images

SEE SOLUTION Check out a sample Q&A here

Knowledge Booster

Learn more about

Need a deep-dive on the concept behind this application? Look no further. Learn more about this topic, civil-engineering and related others by exploring similar questions and additional content below.

Similar questions

Although the constituents of concrete (aggregate and hydrated cement paste) behave in a linear elastic manner if stress is applied to them and the resulting strain is measured, concrete is not a linear elastic material throughout its entire stress-strain curve. What is the main reason for the deviation from this behavior? Interfacial transition zone (ITZ) Incomplete hydration of cementitious phases The loading rate applied according to ASTM C 39 presence of C-S-H very close to the aggregate/paste interface
Which of the following statements is correct? A) Pozzolans react with Calcium Silicate Hydrate (C-S-H) to form Calcium Hydroxide (C-H) B) Pozzolans react with the by-product of cement hydration to produce a denser concrete C) Use of pozzolans in a mix generally improves the durability and strength of the concrete D) b and c
Which of the following directly causes sulfate attack in concrete? CH Delayed ettringite formation CO2 C-S-H
An ASTM cast iron, grade 30, has ultimate strength at tension Sut = 350 MPa, and at compression Suc = 1150 MPa. it carries static loading resulting in the stress state listed below at the critical locations. Using the static failure analysis estimate the factor of safety. σA = 127 MPa, σB = -264 MPa.
Design the concrete mix according to the following conditions: Design environment Tennis court, subjected to freezing Required design strength =21 MPa Slab thickness=300 mm Statistical data indicate a standard deviation of compressive strength of 3.7 MPa is expected (for 50 samples) Only air entrainer is allowed Available materials: Air=7% Air entertainer: Manufacturer specification is 9.0 ML /1% air/100kg cement Slump=50 mm Coarse aggregate: 50 mm nominal maximum size, crushed stone Bulk volume oven-dry specific gravity=2.61, absorption=2.8%, oven-dry rodded density=1870 kg/m3 Moisture content=1% Fine aggregate: Natural sand Bulk oven-dry specific gravity=2.54, absorption=3.4% Moisture content= 4.5% Fineness modulus=2.60 Cement: Type I, relative density=3.1
please answer d,e,f
(a) In general, which provides better fire performance, carbonate or silicate aggregates? Why? (b) Why does fire design incorporate a load reduction factor (Dfire) = 1.0? (c) Two identical beams (Beam 1 is simply supported, and Beam 2 is fully restrained) are heated under similar conditions. What does the mechanical strain equal to in each of these beams? (d) A design office located in Clemson, SC (with a branch in San Francisco, CA) envisions designing a new composite member made of steel and timber. This to-be designed member is expected to be used in wildfire-prone regions primarily for single family homes. Comment on how you would design such a member to achieve superior fire performance. (e) Plot and discuss the expected degradation faces in three bending elements (say, beams) to be made from concrete, steel and timber?
Hardening of concrete is caused by "Hydration" True False
Reinforced concretes are usually attacked by water and rusted. This is due to, a. Low density cements or high porosity that allow water to reach the steel b. The expansion of the rust as it has higher volume than steel push the cement cover and break it c. All the options d. None of the options e. The cover thickness is too small (the steel is too close to the end of the concrete block)
Two pieces of wood, 60 mm by 120 mm each are glued together along the 40° joint. The permissible normal stress in the glue is limited to 100 MPa. The maximum safe load that can be applied at the joint is P+ 40° 60 mm P