Question 1The volume of the passenger compartment of an aircraft is 2100 m³. A piece ofautomatic equipment maintains the air inside the plane at a pressure of 98 kPaand a temperature of 23°C.a) Calculate the mass of the air inside the plane.b) Determine the percent increase in the mass of the air if the pressure isincreased to 101 kPa and the temperature drops to 20°C.

Answered: Image /qna-images/answer/02d29325-61d8-40a2-b80a-6db1365bf007.jpg

Answered: The volume of the passenger compartment…

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

1. Oxygen at 30°C and 300 kPa absolute pressure expands isotherrnally to an absolute pressure of 120 kPa. Determine the final density of the gas. Ans. 1.52 kg/m³ 2. Air is enclosed by a rigid cylinder containing a piston. A pressure gage attached to the cylinder indicates an initial reading of 25 psi. Determine the reading on the gage when the piston has compressed the air to one-third its original volume. Assume the compression process to be isothermal and the local atmospheric pressure to be 14.7 psi. Ans. 104 psig 3. The viscosity of liquids can be measured through the use of a rotating cylinder viscometer of the type illustrated in Fig. P1.3. In this device the outer cylinder is fixed and the inner cylinder is rotated with an angular velocity w. The torque T, required to develop w is measured and the viscosity is calculated from these two measurements. Develop an equation relating u, w, T, e, Ro and Ri. Neglect end effects and assume the velocity distribution in the gap is linear.…
NOTE: Complete manual computation. Show the integration method and derivation of units. ft lb Btu For a certain ideal gas, R = 77.8 lb R and Cp = (0.2 + 0.0002T) lb R %3D It is heated from 40 °F to 140 °F. For 1 Ib mass, find: a. change of internal energy b. change of enthalpy
The Baume (Be) scale was used to determine the specific gravity of wine in the traditional wine-making factory. During the 24-h production, the factory produces 2.861 tonnes of wine at 15°Be. The temperature is the factory is maintained at 22°C. Compute he projected total cost of this quality produce if it can be sold at ₱ 1,687.81 per liter. Type your answer in 2 decimal places only.
i. Draw a P-V graph to represent the changes undergone by the air ii. Calculate the maximum volume of the air. iii. What is the maximum pressure of the air? iv. State how the net work done on the air for the whole process can bedetermined.
431.66-L rigid tank contains 6.42 kg of air at 26.22C. Determine the reading on the pressure gage (kPa) if the atmospheric pressure is 99.13 kPa.
Air contained in a piston-cylinder system undergoes a polytropic process. Pv1.3 = constant P1 = 100 kPa pressure and T1 = 220C temperature to P2 = 500 kPa pressure is compressed. Calculate the specific volume and temperature at the end of the process.
If a piston-cylinder system has V = 0.8m^3 of saturated water vapor at P1 = 250 kPa, at which the piston is sitting on a number of stops. The heat is slowly transferred to steam until the piston begins to move off of the stops at a pressure of P2 = 300 kPa, the heat transfer to steam continues until the volume doubles. a) draw the control volume, with assumed direction of work and heat transfers b) draw P-v diagram c) find final temperature
1. A certain ideal gas X has molecular weight of 10 g/mol and specific heat ratio of 2. Initially, X has pressure of 20OKPA and volume of 2m3. The pressure was doubled during heat transfer. Find the heat transfer if it underwent a process described by a. n=infinity b. n=Cp/Cv c n=3
Problem 2: There is a piston cylinder device that contains 0.03 kg of saturated liquid water. The water or H;O is heated to a final temperature of 300 °C. The piston has a mass of 10.0586 kg and a cross sectional area of 0.001m. The atmospheric pressure is 101.325 kPa. The piston can move upward as water is heated. a) Determine the pressure inside the cylinder by applying Newton's law in vertical direction b) What is the initial temperature of the water if the pressure inside the piston cylinder device is 200 kPa? c) Determine the amount of heat transfer required for the process m-5kg Water Figure for Problem 2
Air occupying a volume of 12 liters at 35 0C is compressed adiabatically to a volume of 4 liters. It is then allowed to expand under isothermal conditions to its original volume. a) Show the process on a Pressure-Volume diagram b) Calculate the final temperature and pressure of the air. Assume γ = 1.44
1. Nitrogen contained in a piston-cylinder device is compressed from 0.5 to 0.2 m³. During the process, the pressure and volume are related by PV2=aV+ b. The values of a and b are given in the table below. Calculate the work done on the nitrogen during this process. (25 Points) Student number 1 210505269 a (kPa.m³) 8.0 b (kPa.m6) 4.0
Air occupying a volume of 12 liters at 35 °C is compressed adiabatically to a volume of 4 liters. It is then allowed to expand under isothermal conditions to its original volume. a) Show the process on a Pressure-Volume diagram b) Calculate the final temperature and pressure of the air. Assume y = 1.44

Recommended textbooks for you

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Elements Of Electromagnetics

Mechanical Engineering

ISBN:

9780190698614

Author:

Sadiku, Matthew N. O.

Publisher:

Oxford University Press

Mechanics of Materials (10th Edition)

Mechanical Engineering

ISBN:

9780134319650

Author:

Russell C. Hibbeler

Publisher:

PEARSON

Thermodynamics: An Engineering Approach

Mechanical Engineering

ISBN:

9781259822674

Author:

Yunus A. Cengel Dr., Michael A. Boles

Publisher:

McGraw-Hill Education

Control Systems Engineering

Mechanical Engineering

ISBN:

9781118170519

Author:

Norman S. Nise

Publisher:

WILEY

Mechanics of Materials (MindTap Course List)

Mechanical Engineering

ISBN:

9781337093347

Author:

Barry J. Goodno, James M. Gere

Publisher:

Cengage Learning

Engineering Mechanics: Statics

Mechanical Engineering

ISBN:

9781118807330

Author:

James L. Meriam, L. G. Kraige, J. N. Bolton

Publisher:

WILEY

SEE MORE TEXTBOOKS