The uniform 16-kg plate is welded to the vertical shaft, which is supported by bearings A and B. Calculate the magnitude of the force supported by bearing B during application of the 100-N-m couple to the shaft. The cable from C to D prevents the plate and shaft from turning and the weight of the assembly is carried entirely by bearing A. 220 mm 100 N-m A 170 mm B 80 mm 600 mm D 480 mm

The uniform 16-kg plate is welded to the vertical shaft, which is supported by bearings A and B. Calculate the magnitude of the force supported by bearing B during application of the 100-N-m couple to the shaft. The cable from C to D prevents the plate and shaft from turning and the weight of the assembly is carried entirely by bearing A. 220 mm 100 N-m A 170 mm B 80 mm 600 mm D 480 mm

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

Need help please include as much work as possible
Determine the force P required to maintain the 215-kg engine in the position for which θ = 28°. The diameter of the pulley at B is negligible
Q11/ It is desired that a person be able to begin closing the van hatch from the open position shown with a 40-N vertical force P. As a design exercise, deter- mine the necessary force in each of the two hy- draulic struts AB. The ma door is 37.5 mm directly below point A. Treat the problem as two-dimensional. center of the 40-kg A 550 mm Hinge axis 600 mm 30° 175 mm E 1125 mm B Strut detail A B Reply...
The shaft, lever, and handle are welded together and constitute a single rigid body. Their combined mass is 31 kg with mass center at G. The assembly is mounted in bearings A and B, and rotation is prevented by link CD. Determine the magnitudes of the forces exerted on the shaft by bearings A and B while the couple is applied to the handle as shown. Would these forces change if the couple were applied to the shaft AB rather than to the handle? 95 mm 405 mm 365 mm 365 mm 510 mm 215 mm 30 N-m 270 mm 270 mm Answers: A = i N B = i
ps: the tolerance is ±1 in the third significant digits
A force of F= -650j and a couple of M = 50i is applied to the assembly shown. Determine the reactions of the journal bearing (A), the thrust bearing (B), and cable CD. Assume the bearings are properly supported. 50 mm 480 mm 300 mm 300 mm 600 mm 220 mm 200 M 200 mm F mm
When the 0.05-kg body is in the position shown, the linear spring is stretched 10 mm. Determine the force P required to break contact at C. Complete so lutions for (a) including the effects of the weight and (b) neglecting the weight.
The shaft, lever, and handle are welded together and constitute a single rigid body. Their combined mass is 40 kg with mass center at G. The assembly is mounted in bearings A and B, and rotation is prevented by link CD. Determine the magnitudes of the forces exerted on the shaft by bearings A and B while the couple is applied to the handle as shown. Would these forces change if the couple were applied to the shaft AB rather than to the handle? 100 mm 400 mm 280 mm 280 mm 620 mm 225 mm 33N-m 180 mm 180 mm Answers: A = i B = N
The ramp is used as passengers board a small commuter airplane. The total mass of the ramp and six passengers is 730 kg with a mass center at G. Determine the force in the hydraulic cylinder AB (positive if in tension, negative if in compression) and the magnitude of the pin reaction at C.
The 40-kg uniform triangular plate is supported by two small hinges A and B and the cable system shown. For the horizontal position of the plate, determine all hinge reactions and the tension T in the cable. Hinge A can resist axial thrust, but hinge B cannot. See Table D/3 in Appendix D for the mass-center location of a triangular plate. Answers: Ax= Ay- A₂ 0.43 m 0.20 m By B₂= 0.20 m 0.43 m T= 0.91 m. Z Z N N z z N N N N 1.30 m