Now, for the same J-shaped member, determine MA, MA and MA, the couple moments at the support about the x, y, and z axes, respectively, required to keep the system in equilibrium. The cylinder weighs WB = 24.0 N; a vertical force F = 7.60 N acts at C; and the member's dimensions are w = 0.450 m ,l = 2.00 m , and h = 0.600 m

Now, for the same J-shaped member, determine MA, MA and MA, the couple moments at the support about the x, y, and z axes, respectively, required to keep the system in equilibrium. The cylinder weighs WB = 24.0 N; a vertical force F = 7.60 N acts at C; and the member's dimensions are w = 0.450 m ,l = 2.00 m , and h = 0.600 m

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The bent rod in Fig. a is supported at A by a journal bearing, at D by a ball-and-socket joint, and at B by means of cable BC. Using only one equilibrium equation, obtain a direct solution for the tension in cable BC. The bearing at A is capable of exerting force components only in the z and y directions since it is properly aligned on the shaft. In other words, no couple moments are required at this support. 1m B. 0.5 m Free-Body Diagram. As shown in Fig. b, there are six unknowns 05 m Equations of Equilibrium. The cable tension Tg may be obtained directly by summing moments about an axis that passes through points D and A. Why? 00 kg (a) Since the moment arms from the axis to T, and W are easy to obtain, we can determine this result using a scalar analysis. As shown,Fig. b EMDA = 0; Tạ(1 m sin 45°) – 981 N(0.5 m sin 45°) = 0 T = 490.5 N 0.5 m W 981 N 05 m D, (b)
Q3 - The uniform bar OC of length L and mass (m ) pivots freely about a horizontal axis through O. If the spring of modulus k is unstretched when C is coincident with A, determine the tension T required to hold the bar in the position shown. The diameter of the small pulley at D| is negligible. T D L/2 45° B 30 L/2 mg А wwww
Find the horizontal and vertical components of the reaction at support G (+x to the right, +y upward), given: M = 100 N·m, P1 = 80 N, P2 = 70 N, P3 = 50 N, L1 = 3 m, L2 = 4 m, L3 = 3 m, L4 = 3 m, L5 = 2 m, L6 = 3 m, θ = 35 °, x,y,h = 12,5,13
hin the figure, a 10 meters bar of negligible weight supports a uniform load of w1=5N from A to the center and a varying load of w2=10N from center to B, and with a concentrated load of F= 50N distance from 3meters from A. An additional Moment of 15 N/m is acting on B. Determine the Resultant Force of the system. * F W2 3 me ter W1 AV V В M 5 meter 10 Meter 605.833 N.m 605.338 N.m 506.338 N.m 506.833 N.m O none of the above
An architecture student working at a drafting table requires some muscle action in order to support her head. As shown in the figure, three forces act on her head. If the force provided by muscles is F = 70 N and the weight of her head is W = 40 N, determine the magnitude and direction of the force provided by the upper vertebrae F, to hold her head stationary. Assume that this force acts along a line through the center of mass of her head as do the weight and muscle force. (Assume the +x-axis to be to the right.) magnitude direction ° measured clockwise from the -x-axis CG
If W1 = 1800 lb and the system is in equilibrium, calculate the moment about point P in Ib-ft 6 ft 50° B W W2 Answer in + value if the moment is clockwise, otherwise answer in - value for counter clockwise moment 86% 27°C Partly sunny LEGION 11 ow E6 のロh E6O : TEB (14 TEB 4+ TEB TEB = FROM EQ (3) ED = 213 ED = 0.604
The mass center Gof the 1490-kg rear-engine car is located as shown in the figure. Determine the normal force under each tire when the car is in equilibrium. State any assumptions. -1290 mm-976 mm- Answers: Normal force under each of the front tires: N; = i N Normal force under each of the rear tires: N, = N z z
1. Determine the magnitude and direction with respect to the +x axis on the reaction at A and at C. Note that the body is supported by pin at A and a roller at C. The body's weight is negligible. 2.4 kN-m 40° -200-250- Dimensions in mm -300 B 3 kN
Cable AB passes over the small ideal pulley C without a change in its tension. What length of cable CD is required for static equilibrium in the position shown? What is the tension Tin cable CD? 3.7' Answers: LCD= TCD= i i A 48° B 69 lb ft lb D
Q2. Determine all forces acting on body A for the system shown in figure 2. Body A weighs 200 N and the cylinder B weighs 500 N. assume all the contact surfaces are smooth. 777TT ring 24 Cable 7 A r= 0.5 m 30 0.5 m B. 2 m 1 m 1 m 30
A ladder AB is leaning against a smooth vertical wall at A and is resting on a horizontal floor at B. A person of mass 81.50 kg exerts a vertical force at C.. person applies a horizontal force of 240 N at D Another 2.5m -END- 1.5m to help reduce the horizontal pressure against the block at B. Compute the reacting forces at A and B. 900 N = 81.50 kg x 9.81 0.5m 0.5m 240N block