mass The power unit A of the tractor-scraper has a mass of 5.9 Mg with mass center at G₁. The fully loaded trailer-scraper unit B has a of 22.7 Mg with mass center at G₂. Positioning of the scraper is controlled by two hydraulic cylinders EF, one on each side of the machine. Calculate the compression F in each of the cylinders and the magnitude of the force supported by each of the pins at H, one on each side. Assume that the wheels are free to turn so that there are no horizontal components of force under the wheels. Answers: Fa H= i 1480 1480 11701480540 Dimensions in millimeters kN 1 kN

mass The power unit A of the tractor-scraper has a mass of 5.9 Mg with mass center at G₁. The fully loaded trailer-scraper unit B has a of 22.7 Mg with mass center at G₂. Positioning of the scraper is controlled by two hydraulic cylinders EF, one on each side of the machine. Calculate the compression F in each of the cylinders and the magnitude of the force supported by each of the pins at H, one on each side. Assume that the wheels are free to turn so that there are no horizontal components of force under the wheels. Answers: Fa H= i 1480 1480 11701480540 Dimensions in millimeters kN 1 kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The wall-mounted 3kg light fixture has its mass centre at G. Determine the vector reactions at A. -10 mm 100 mm- 200 mm 230 mm Razi + Rayj, in newtons, determine the components of the reaction force Raz and Ray- If this vector reaction force can be written as R. Choose.. Ray Choose... Raz
The jib crane is designed for a maximum capacity of 14 kN, and its uniform I-beam has a mass of 270 kg. Plot the magnitude R of the force on the pin at A as a function of x through its operating range of x = 0.2 m to x = 4.0 m. On the same set of axes, plot the x- and y-components of the pin reaction at A. Do these plots on a separate piece of paper. Then answer the following questions in Wiley Plus as a check for your work. (You can disregard the plot, I only need a, b, c, and d)
The portable floor crane in the automotive shop is lifting a 350-lb engine. For the position shown compute the magnitude of the force supported by the pin at C and the oil pressure p against the 3.46-in.-diameter piston of the hydraulic-cylinder unit AB. Assume a = 7 in., b = 34 in., c = 17 in., e = 36 in., and θ= 32°.
The position of the head and neck and the forces acting on the head are shown in the figure. The center of gravity of the head of mass m=9 kg is located at point C. The joint reaction force of F J = 150 N, which makes an angle of α = 30° with the vertical from the point B, is acting on the skull by the neck extensor muscles. The center of the atlantooccipital joint is located at point B. For this flexion position of the head, the neck muscle force FM, which makes an angle of γ with the horizontal from the point A , is effective . (Take the gravitational acceleration g as 9.81 m/s 2. ) Accordingly; a) Calculate the angle γ of the muscle force F M with the horizontal. b) Calculate the muscle strength F M. (Write your result in N units.)
The needle-nose pliers are used to either cut objects at location A or grip objects at location B. Compute (a) the cutting force at A and (b) the gripping force at B in terms of the applied force F. Determine the magnitude of the pin reaction at O in both cases. Neglect the effects of the slight opening of the jaws to accommodate the gripped items. B Answers: 66 mm 14 mm A O (a) The cutting force at A: 103 mm FA i (b) The gripping force at B: FB = i F F F The pin reaction at O: Fo- i F The pin reaction at O: Foi F F
5. The figure below represents the anatomy of the lower limb when balanced on your toes and the body weight acts through the tibia. The Achilles Tendon makes an angle (0) of 8° with the vertical and for this foot x1 is 6.2 cm and x2 is 12.3 cm. Calf Muscle Tibia Achilles Tendon Calculate the tension (T) in the Achilles Tendon if a 70 kg man stands on the toes of both feet. Using the values in this example what is the mechanical advantage for this lever and describe what that means in terms of the efficiency of the lever.
Very urgent The elements of the spring loaded mechanism for the car tailgate are shown in the figure. For the shown equilibrium state, two curved springs are used on the AB connection. The mass of the tailgate is 18 kg with the center of mass G. Calculate the loads carried by the O connection. The influence of the weights of the other components is negligible.
Free Body Diagram
Do not give answer in image and hand writing
End B of the uniform 2.7-kg bar AB is connected to a small roller that moves in a horizontal slot. The other end of the bar is pinned to the homogeneous 1.8-kg disk that rolls without slipping on the vertical surface. The spring attached to A has a free length of 0.3 m and a stiffness of 58 N/m. After the system is becomes horizontal. Determine the magnitude of the force P that acts on the bar at B. 2.1 m 0.24 m 0.9 m www 1.8 kg 1.5 m 2.7 kg P
The square steel plate has a mass of 1980 kg with mass center at its center G. Calculate the tension in each of the three cables with which the plate is lifted while remaining horizontal.
A 9.0 m beam of uniform width is supported as shown by supports S1 and S2. Given the weight of the beam is 200 N and is loaded as shown, determine the normal forces, 5. S1 and S2, exerted on the beam. Assume the weight of the beam acts at the midpoint of the beam. Determine if it is possible to move the 300 N object to a location on the beam which will result in the beam "tipping." S2 S1 1.0m 3.0m - -3.5m