The machine shown is used for moving heavy items such as pallets of bricks around construction sites. Determine the force in the single hydraulic cylinder CD (positive if in tension, negative if in compresssion). The mass of the cube of bricks is 1980 kg with mass center at G2. You may neglect the effects of the mass of the forklift components. Assume a = 770 mm, b = 185 mm, c = 500 mm, d = 45 mm, e = 810 mm. a E- D Answer: CD = i kN

The machine shown is used for moving heavy items such as pallets of bricks around construction sites. Determine the force in the single hydraulic cylinder CD (positive if in tension, negative if in compresssion). The mass of the cube of bricks is 1980 kg with mass center at G2. You may neglect the effects of the mass of the forklift components. Assume a = 770 mm, b = 185 mm, c = 500 mm, d = 45 mm, e = 810 mm. a E- D Answer: CD = i kN

Elements Of Electromagnetics

7th Edition

ISBN:9780190698614

Author:Sadiku, Matthew N. O.

Publisher:Sadiku, Matthew N. O.

ChapterMA: Math Assessment

Section: Chapter Questions

Problem 1.1MA

See similar textbooks

Similar questions

The machine shown is used to help load luggage into airliners. The combined mass of the conveyor and luggage is 110 kg with mass center at G. Determine and plot the force in the hydruaulic cylinder BC (report your answer as a positive value) as a function of over the range 5° 0 ≤ 36°, then answer the questions. Assume DE = 2070 mm, CD = 1280 mm, c = 1680 mm, d = 1130 mm, e = 570 mm, f = 2380 mm. t Questions: E B i D If 0 = 11°, BC = If 0 = 21°, BC = i Over this range, the maximum value for BC = i N N N and occurs when 8 =
A sled with a mass of 25.0 kg rests on a horizontal sheet of essentially frictionless ice. It is attached by a 5.00-m rope to a post set in the ice. Once given a push, the sled revolves uniformly in a circle around the post as shown in the figure. If the sled makes five complete revolutions every minute, find the force F exerted on it by the cord. R-
6.62 Neglect the mass of the pulleys and the link. The block has a weight of 230 lb and the cord is attached to the pin at B. The pulleys have radii of r1 = 2 in. and r2 = 1 in. Determine the force P on the cord. Determine the angle θ that the pulley-supporting link AB makes with the vertical.
The following system is in static equilibrium with the strings AB, BC, and CD connected to support the 40N and 50N weights as shown. The middle string BC is exactly horizontal, and points A and D are connected to a rigid support. Calculate the tension forces T₁, T₂, T3, and the angle 8. T₁ A 35° T₁ 35⁰ B 40 N 40 N T2 T2 0 T₂ C 50 N 50 N D T3 T3
ASAP
Very urgent The elements of the spring loaded mechanism for the car tailgate are shown in the figure. For the shown equilibrium state, two curved springs are used on the AB connection. The mass of the tailgate is 18 kg with the center of mass G. Calculate the loads carried by the O connection. The influence of the weights of the other components is negligible.
End B of the uniform 2.7-kg bar AB is connected to a small roller that moves in a horizontal slot. The other end of the bar is pinned to the homogeneous 1.8-kg disk that rolls without slipping on the vertical surface. The spring attached to A has a free length of 0.3 m and a stiffness of 58 N/m. After the system is becomes horizontal. Determine the magnitude of the force P that acts on the bar at B. 2.1 m 0.24 m 0.9 m www 1.8 kg 1.5 m 2.7 kg P
The homogeneous box has mass m. The magnitude of force Pis slowly increased until motion occurs. Motion could occur as slipping or tipping and you must decide which occurs first. Find the value of P which first causes motion. P А 30° d = 0.40 B 2.2 d Answer: P = i mg
Frames & Machines The truck shown is used to deliver food to aircraft. The elevated unit weighs 2000 Ib with center of gravity at G. 1- Derive the expression for the force in the hydraulic cylinder AB as a function of 0 (the angle that member FD makes with the horizontal). 2- Plot the force over the range 0° < 0 < 45° and discuss your observations. Note: | would suggest that you first solve the problem based on the position (angle) shown. You will need to determine the length of members FD and FB before solving the problem for arbitrary 0. Note that the location of the roller at D and hence the force reactions will change as 0 varies. 40" 17" 57" C 54" E 54" H AB
The square steel plate has a mass of 1980 kg with mass center at its center G. Calculate the tension in each of the three cables with which the plate is lifted while remaining horizontal.
A crate with dimensions l = 0.50 m and h = 0.75 m rests on a plane that is inclined by θ = 30◦ from thehorizontal. The crate is in equilibrium, but if the crate were too tall, it will fall over down the slope.Find the effective point of application of the normal force on the crate, i.e., where is the normal force actingon the crate, keeping the crate in equilibrium? Hint: choose the crate’s center of mass as the axis of rotation.
One of the smooth vertical walls supporting end B of the 230-kg uniform shaft is turned through a 21° angle as shown here. End A is supported by the ball-and-socket connection in the horizontal x-y plane. Calculate the magnitudes of the forces P and R exerted on the ball end B of the shaft by the vertical walls C and D, respectively. Assume a = 5.6 m, b = 2.3 m, L = 6.5 m, and 0 = 21° Answers: P = 2245 R = H. B a L D N A !N b