4/70 Compute the force supported by the pin at A for the slip-joint pliers under a grip of 100 N. 270 mm 45° 100 N 60 mm Co A 100 N

Q: a b c d h   82 mm     139 mm     39 mm     18 mm     33 mm   Clamps like the one shown are commonly…

A:

Q: QUESTION 2: For the nose landing gear of an aircraft shown in the figure, calculate the internal…

A:

Q: A 50 lb force is applied to the wrench. Solve for the pin reaction at B as well as the gripping…

A:

Q: A 60⁰ B 60⁰ 60% 60⁰ lokN 60⁰ 60% 60⁰ 15 KN 60⁰ 60°

A: To Find-All the internal forces in every cable in the figure below.

Q: Q2: Determine the force supported by each member shown in Figure 2 by using method of joint. 5m 1 AN…

A:

Q: Please write the problem on paper, I do not like it when it is typed out on the computer. Need help…

A:

Q: Refer to the figure, what is the reaction at pin C in kN?

A: To find: The reaction at the pin C. Calculation: Consider an free body diagram below: Here, RDH…

Q: 6. DETERMINE THE COMPONENTS OF THE REACTION ON PIN A AND THE REACTION AT THE ROLLER B SHOWN IN…

A: Let the compoents of reaction at A be Ax and Ay and the reaction at B is FB.

Q: A Mechanical Engineer wants to compute the Tension at AB and AC. He identifies that the value of…

A: Given:

Q: Compute the work done (J) by the moment when the disk undergoes the specified displacement.

A: Given data asper question The radius of roller =0.2 m Moment =100 Nm

Q: S Q2. The double pulleys are fastened together to form a rigid unit. If V₁ = 9 and VB = 3 compute…

A: The answer is given in the below

Q: Rod AB is supported by a pin and bracket at A and rests against a frictionless peg at C. AO с 160 mm…

A:

Q: 6-29E. For the crane system of Figure 6-27, determine the hydraulic cylinder force required to lift…

A: For the crane system of Figure 6-27,Determine the hydraulic cylinder force required to lift the…

Q: Determine the forces at all joints 3 in G 1000 Ib B 10 in 5 in 5in

A: Taking vertical and horizontal reaction at A , Va and Ha Taking vertical and horizontal reaction at…

Q: Situation 5. Determine the member forces CD and GF using any method. Indicate if (T) or (C). 2 kN…

A: Given: P1 = 2 KN P2 = 1.5 KN To find: FCD and FGF

Q: Refer to the truss shown in Figure 1-101, and compute the force in members BD, DC, and CE by the…

A:

Q: Problem 6 Refer to the figure to the right for: The mobile crane has a weight of 190000 lb and…

A:

Q: Determine the reactions at the pin support and the applied moment if the bar of Figure 3 has a mass…

A: Given: The mass of bar, m = 50 g The angle, θ = 15° The angular acceleration of bar, α’ = 20 rda/s^2

Q: 3. In the given 15.0 meter slab and inclined 10°with the horizontal, the ends are resting on…

A:

Q: F E 3 ft A C В 4 ft 4 ft 800 lb

A:

Q: Compute the 1. force in each member. 2000 lb 3000 1b

A:

Q: Draw the free body diagram Always use 3 decimal place

A:

Q: 1000 N 90 2000 N 90 1000 N 90 90 90° 130° 30 GG 12 m 12 m 12 m 1000 N

A:

Q: 9" 800 lb C В 4'- A 3'

A:

Q: Write the matrix equations in terms of stress tensors for the three equations

A: consider three mutual perpendicular normal stresses σxx , σyy , σzz acts at a component along x, y…

Q: The overhang beam is supported by a pin at point A and a roller at point B. A distributed load is…

A:

Q: 6-101. If a clamping force of 300 N is required at A, determine the amount of force F that must be…

A: The clamping force of 300 N is required at A.To Find:The amount of force F that must be applied to…

Q: 3. The pruning mechanism of a pole saw is shown as it cuts a branch S. For the particular position…

A:

Q: The nail cutter consists of the handle and the two cutting blades (Eigure 1) Figure 6 mm 6 mm -36 mm…

A: According to the given data F=6 N We need to find Force on the fingernail by the cutter

Q: using the Method

A: ∑Fx=088.87+CE+CFsin38.3°=088.87+CE+(-33.6)sin38.3°=0CE=-89.17KN∑Fx=0-CFcos38.3°-CB = 0…

Q: A 10.5 ft B 200 lb 2 ft 2 ft 1 ft 1 ft 1 ft, F

A: Given: The value of the weight is 200 lb.

Q: 3 digits behind comma From the given figure, F = 100 N. • Draw the FBD 1000 mm • Draw the action…

A: given data: F=100N AB=125mm BC=1000mm force at B?? force at A?? RAV=vertical force at point…

Q: Find the magnitude of the pressure force acting on the gate shown in the figure and then calculate…

A: Height of latch from the hinge = 4 ft Height of water column above the hinge = 3.6 ft

Q: The bar is made from welding two uniform 40 lb bars together. Calculate the magnitude of the pin…

A:

Q: Please help me to answer all the needed components  Instruction: Calculate the components of forces…

A:

Q: The signboard truss is designed to support a horizontal wind load of 700 lb. If the resultant of…

A:

Q: The uniform crate shown in the figure weighs 600 lb. It is pulled up the incline by a counterweight…

A: To find: The maximum and minimum values of d so that the crate does not tip over as it slides up the…

Axial Load

When a bar of the uniform cross-section is acted by a load, such that the load acts along the longitudinal axis of the bar, such kinds of loadings are known as axial loadings. In general terms, a load is an external force acting on a component. An axial load acts perpendicular to the geometric cross-section of the component. Based on the direction of the application of the load, an axial load can be tensile or compressive. The analysis of bodies under the action of axial loads is generally studied under the branch of mechanics, known as statics.