The ultimate shearing stress of the rivet used to join plates is 22 ksi. For a factor of safety of 2, calculate the safe shearing resistance of a unit strip of a single-riveted lap joint in which the plate thickness of ¼ in, the pitch joint of ¾ in, and the diameter of the rivet hole is 11/16 inch

The ultimate shearing stress of the rivet used to join plates is 22 ksi. For a factor of safety of 2, calculate the safe shearing resistance of a unit strip of a single-riveted lap joint in which the plate thickness of ¼ in, the pitch joint of ¾ in, and the diameter of the rivet hole is 11/16 inch

Welding: Principles and Applications (MindTap Course List)

8th Edition

ISBN:9781305494695

Author:Larry Jeffus

Publisher:Larry Jeffus

Chapter22: Welding Joint Design And Welding Symbols

Section: Chapter Questions

Problem 4R: Sketch a V-grooved butt joint, and label all of the joint's dimensions.

See similar textbooks

Similar questions

Design a single riveted lap joint to connect two mild steel plates, 14.5 mm thick, the joint being designed for maximum efficiency. The allowable stresses are σt = 55 N/mm2 , = 32.5 N/mm2 and σc = 63.5 N/mm2 . Also calculate the minimum force per pitch which will rupture the joint
QUESTION 20 Below is an image showing two 4 mm thick sheets joint together using double rivets. If the rivets were made of st
Write legibly, provide step by step manual solution, and diagram for below given problem. An 18mm diameter rivet is used to fasten two 22mm thick plate. If the shearing stress is 60MPa. What tensile force applied each plate to shear the bolt? (Ans. F = 15.27KN)
5. A flanged bolt coupling between two shafts carries 12 bolts in a diameter of 18-in. The shafts carry a torque of 50,000 ft.lb. Assuming that this torque is transmitted by shear across the 12 bolts and that these bolts are to be designed for a shear stress of 3,000 psi, what must be the bolt diameter? 18 in Figure 3.6.4 6. A plate is fastened to a fixed member by four 25 – mm diameter rivets arranged ss shown. Compute the maximum and minimum shearing stresses developed? |20 kN 20 kN Figure 3.6.5
10. Two tie bars are connected together by 0.5cm fillet welds around the end of 1 bar and the inside of a slot machined in the same bar. Estimate the strength of the connection in tension if the shearing stress in the welds is limited to 75MPa. 450m 10cm 8cm
2. A 30-mm bolt with an initial tension of 35 kN is subjected to several types of stresses during initial tightening or due to screwing up forces. If the bolt has a core diameter of 25.7 mm and considering 5 threads are already engaged with the nut, calculate the shear stress across the thread and the crushing stress between the threads. Assume 3.5 mm as the width of the thread section at the root.
4. Determine the efficiency of the riveted butt joint with 20 mm main plate, 12 mm cover plates and 25 mm alloy steel rivets as shown in Fig. 4. Take allowable stress in shear for the rivets as 82.7 MPa, tensile strength of the plates as 144.8 MPa and allowable bearing stress as 89.6 MPa. 8 25 mm rivetsł 150 mm 12 mm 20 mm Fig. 4. оо
8. Re If a steel bolt is tested in single shear and fails at a load of 25 kips, at what load would we expect an identical bolt to fail if it is subjected to double shear?
Q1/ Calculate the forces in all rivets for the rivet group shown. 24KN 600mm 300mm 240mm
A double riveted single cover butt joint (zig zag arrangement), is used for connecting two plates 15mm thick. The diameter of the rivets is 20mm and the pitch is 100mm. Draw the joint with hand sketch and calculate the efficiency of the joint, if permissible stresses are as below: Permissible shearing stress in rivets = 120Mpa Permissible tensile stress in plate = 150MPa Permissible crushing stress in rivets = 210MPa
مقاومة المواد
Need solution through 15 min